Airtac TACE Guided Compact Cylinder TACE63X45S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X45S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 45mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke45 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X45S
The AirTAC TACE63X45S is a double acting, non-rotating compact cylinder built to ISO 21287: a 63 mm bore pushing 1558.6 N at 0.5 MPa (2182.1 N at 0.7 MPa) through a 45 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square with no external guide. Its short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guards and gantries where a full-length cylinder will not fit.
For real-world sizing, plan on roughly 935 N of usable push at 0.5 MPa, and expect about 79 kg of vertical lift with a 2:1 margin. The 16 mm rod is S45C steel with hard chrome and a female M10x1.5 thread; the 1/8" PT port feeds air filtered to 40 um across 0.15-1.0 MPa (22-145 psi). This -S model carries the magnet, so CMSE / DMSE reed or solid-state switches can be mounted directly in the body slots, and a fixed TPU bumper absorbs end-of-stroke energy at both ends.
Airtac TACE Guided Compact Cylinder TACE63X45S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X45S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 45 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X45S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X45S Is Used
Connector press station
On an electronics assembly line, the twin-guide yoke presses board connectors square into plastic housings with 1558.6 N at 0.5 MPa over a short 45 mm throw.
CNC casting clamp fixture
Clamps aluminium castings in a machining fixture without hydraulics: about 935 N of usable force holds the part while the twin guide rods stop the clamp plate twisting.
Carton ejector on a packing line
Pushes filled cartons off a conveyor lane at 30-500 mm/s; the 45 mm stroke matches the lane width and a CMSE switch confirms each eject via the fitted magnet.
Is the Airtac TACE Guided Compact Cylinder TACE63X45S the Right Cylinder?
At 63 mm bore this size sits between the 50 mm (981.7 N push at 0.5 MPa) and the 80 mm (2513.3 N push at 0.5 MPa) versions, so step down when the job needs under about 980 N and up when it needs over 1550 N. Speed runs 30-500 mm/s on 0.15-1.0 MPa (22-145 psi) air. The piston drifts if air is lost and holds nothing on its own, so add a rod lock or pilot check valve wherever a load must stay put. FB flange, CA/CB clevis, CR and FTC mountings bolt to the covers, and the fitted -S magnet lets CMSE / DMSE switches clamp onto the body slots without extra brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X45S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push rises to 2182.1 N and pull to 2041.3 N. The theoretical maximum at 1.0 MPa is 317.9 kgf. For sizing, treat about 935 N as the usable push at 0.5 MPa, which is roughly 79 kg of vertical lift with a 2:1 margin.
It is an ISO 21287 short-body cylinder whose hard-anodized aluminium barrel saves about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper at each end absorbs end-of-stroke energy. Because this is the -S version, the magnet is fitted and CMSE / DMSE reed or solid-state switches mount in the body slots; FB, CA, CB, CR and FTC mountings are available.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X45S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.