Airtac TACE Guided Compact Cylinder TACE63X60
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X60 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 60mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X60
The AirTAC TACE63X60 is a double acting, non-rotating compact cylinder built to ISO 21287: its 63 mm bore drives the 16 mm rod with 1558.6 N of push and 1458.1 N of pull at 0.5 MPa, rising to 2182.1 N and 2041.3 N at 0.7 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without any external guide. The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guards and gantries a full-length body cannot enter.
For sizing, plan on roughly 935 N of usable thrust at 0.5 MPa - about 0.6 of the push rating - and note the same force lifts about 158 kg vertically; halve that to roughly 79 kg for a 2:1 margin against a real part weight. The 60 mm stroke sits well inside the 250 mm standard range for this bore, air ports are 1/8" PT, the rod end carries a female M10x1.5 thread, and speed runs 30-500 mm/s across 0.15-1.0 MPa (22-145 psi). A fixed TPU bumper absorbs end-of-stroke energy at both ends, and the optional -S magnet enables CMSE / DMSE switches - without that code no sensor can be mounted.
Airtac TACE Guided Compact Cylinder TACE63X60 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X60 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 60 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X60
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X60 Is Used
Press-fit staking on an automotive assembly cell
A 60 mm stroke with 1558.6 N of push at 0.5 MPa presses bearings or stakes clips into housings, while the twin-guide yoke keeps the punch from rotating or racking under side load.
Clamping large aluminium castings on a CNC fixture
Two TACE63X60 units squeeze a casting against hard stops with about 935 N of usable clamp force each, and the short ISO 21287 body tucks under the fixture plate where space is scarce.
Lift-and-lower of battery modules on an EV line
The push force lifts about 79 kg vertically with a 2:1 margin, and the 60 mm stroke raises modules between a conveyor and an inspection station; a pilot check valve holds the load if air drops.
Is the Airtac TACE Guided Compact Cylinder TACE63X60 the Right Cylinder?
If 1558.6 N of push at 0.5 MPa is more than the job needs, the bore 50 TACE still delivers 981.7 N; if the part is heavier or the stroke longer, step up to bore 80 for 2513.3 N. Remember the rod drifts when air is lost - this cylinder never holds position - so add a rod lock or pilot check valve wherever a load must stay put between cycles. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and ordering the -S code is what puts the magnet inside for CMSE / DMSE position switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X60 FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push rises to 2182.1 N with pull at 2041.3 N. The theoretical maximum at 1.0 MPa is 317.9 kgf. Operating pressure spans 0.15-1.0 MPa (22-145 psi), proof pressure is 1.5 MPa (215 psi), and speed runs 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures and guarded cells. The fixed TPU pad at each end only decelerates the piston at stroke ends - it never locks or brakes a load, and the rod drifts if air is lost, so fit a rod lock or pilot check valve where holding matters. Mounting is FB flange, CA/CB clevis, CR or FTC, and only the optional -S magnet allows CMSE / DMSE switches; this model ships without it.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X60
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.