Airtac TACE Guided Compact Cylinder TACE63X80S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X80S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X80S
The TACE63X80S is a double acting, non-rotating compact cylinder built to ISO 21287, with a 63 mm bore and an 80 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push rises to 2182.1 N, with a theoretical maximum of 317.9 kgf at 1.0 MPa.
For real work, plan on roughly 935 N at 0.5 MPa (about 0.6 of the push force), which corresponds to lifting about 79 kg vertically with a 2:1 margin. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries. A hard-anodized aluminium body carries the S45C hard-chrome rod, a fixed TPU bumper sits at both ends, and the fitted -S magnet accepts CMSE / DMSE switches for end-position feedback. Speed runs 30-500 mm/s across 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE63X80S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X80S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 80 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X80S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X80S Is Used
Bearing press-fit in electric motor housings
A 1558.6 N push at 0.5 MPa seats ball bearings into 6200-series housing bores on a stator assembly cell, while the twin-guide yoke keeps the press anvil square to the bore.
Pallet clamping on a bottling line
The 80 mm stroke clamps shrink-wrapped tray stacks against a fixed stop before stretch wrapping, and the fitted -S magnet with a DMSE switch confirms full clamp before the wrapper starts.
Stopper gates on an automotive assembly conveyor
Raising and lowering a roller-conveyor stopper between car bodies, the non-rotating guide rods hold the gate blade level under side load from misaligned pallets.
Is the Airtac TACE Guided Compact Cylinder TACE63X80S the Right Cylinder?
Size down to the TACE50 when 981.7 N push at 0.5 MPa is enough, or step up to the TACE80 at 2513.3 N for heavier press work; this 63 mm bore sits between them at 1558.6 N. The 80 mm stroke is within the standard range for this bore, so no made-to-order build is needed. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve wherever a load must stay held. Mounting options are FB flange, CA/CB clevis, CR and FTC, with a female M10x1.5 rod thread and a 1/8" PT port. Because the -S magnet is fitted on this model, CMSE / DMSE switches can be clipped straight onto the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X80S FAQ
At 0.5 MPa the 63 mm bore pushes 1558.6 N and pulls 1458.1 N. At 0.7 MPa push is 2182.1 N and pull is 2041.3 N. The theoretical maximum is 317.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed runs 30-500 mm/s on air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which helps in tight jigs and gantries. The hard-anodized aluminium body carries an S45C hard-chrome rod, with a fixed TPU bumper at each end. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the rod end is a female M10x1.5 thread and the port is 1/8" PT. The -S magnet fitted on this model lets CMSE / DMSE reed or solid-state switches mount in the body slots for position signals.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X80S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.