Airtac TACE Guided Compact Cylinder TACE63X90S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X90S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X90S
The TACE63X90S is a double acting, non-rotating compact cylinder built to ISO 21287: a 63 mm bore and 90 mm stroke in a hard-anodized aluminium body with an S45C hard-chrome plated 16 mm rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures rise to 2182.1 N and 2041.3 N, with a theoretical ceiling of 317.9 kgf at 1.0 MPa.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and guarding where a full-length cylinder will not fit. Plan on roughly 935 N of usable push at 0.5 MPa, about 0.6 of the rating, which lifts about 79 kg vertically with a 2:1 margin. Air supply runs 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, the port is 1/8 inch PT, and the rod end carries a female M10x1.5 thread. This model carries the -S magnet, so CMSE / DMSE switches can be mounted for end-of-stroke signals, and a fixed TPU bumper at each end absorbs stroke-end impact.
Airtac TACE Guided Compact Cylinder TACE63X90S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X90S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 90 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X90S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X90S Is Used
Press-fitting bushings into aluminium housings
On an automotive subassembly line, the 1558.6 N push at 0.5 MPa seats light bushings, while the twin-guide yoke keeps the arbor square to the bore so parts are not skewed.
Tray ejection on a packaging conveyor
A 90 mm stroke clears the conveyor lane to push filled trays into a lane diverter, and the non-rotating pusher plate stays aligned run after run without an external guide.
Clamping door panels in a welding fixture
Guide rods on the yoke carry the side load of a clamp arm on sheet-metal panels, holding the fixture square through spot-welding cycles at 30-500 mm/s.
Is the Airtac TACE Guided Compact Cylinder TACE63X90S the Right Cylinder?
Step down to the TACE50 when the job is lighter clamping: it pushes 981.7 N at 0.5 MPa. Step up to the TACE80, which delivers 2513.3 N at 0.5 MPa, once the load grows beyond what this 63 mm bore can cycle comfortably. The piston drifts if air is lost, so it is not a position lock - add a rod lock or pilot check valve where a load must be held. FB flange, CA/CB clevis, CR and FTC mountings suit this bore, and because the -S magnet is fitted on this model, CMSE / DMSE switches report stroke end without extra tooling.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X90S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N. At 0.7 MPa push rises to 2182.1 N with 2041.3 N on the pull stroke, and the theoretical maximum is 317.9 kgf at 1.0 MPa. For real work, plan on about 935 N, roughly 0.6 of the push rating, which lifts about 79 kg vertically with a 2:1 margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each stroke end to absorb impact. Mounting options are FB flange, CA/CB clevis, CR and FTC. Because this model carries the -S magnet, CMSE / DMSE reed or solid-state switches can be clamped to the body slots for end-of-stroke signals.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.