Airtac TACE Guided Compact Cylinder TACE80X100
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X100 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 100mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke100 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X100
A double acting, non-rotating compact cylinder built to ISO 21287, the TACE80X100 pairs an 80 mm bore and 100 mm stroke with a 20 mm hard-chrome-plated S45C rod. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures rise to 3518.6 N and 3298.7 N, with a theoretical peak of 512.6 kgf at 1.0 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight presses, guards and gantries. Plan on roughly 1508 N (about 153 kg) of usable push at 0.5 MPa rather than the full rating - in vertical terms that means lifting about 128 kg with margin to spare. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the hard-anodized aluminium body with 1/4" PT ports runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s.
Airtac TACE Guided Compact Cylinder TACE80X100 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X100 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X100
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X100 Is Used
Staking and swaging press
With 2513.3 N of push at 0.5 MPa, the 80 mm bore drives a small staking head that crimps terminals or rivets on an electronics assembly line, while the 100 mm stroke retracts far enough to clear the part for manual loading.
Weld fixture clamping
The twin-guide yoke holds a clamp arm square on automotive sheet-metal fixtures, taking side load without a separate linear guide, and the 1/4" PT ports keep air plumbing compact inside the fixture frame.
Vertical part lifting
In a palletizing cell this cylinder lifts about 128 kg vertically at 0.5 MPa with margin to spare; fit a pilot check valve on the extend line, since the piston will drift down if supply air is lost mid-lift.
Is the Airtac TACE Guided Compact Cylinder TACE80X100 the Right Cylinder?
Against the 63 mm bore (1558.6 N push at 0.5 MPa) this 80 mm unit delivers about 60% more force; step up to the 100 mm bore (3927.0 N at 0.5 MPa) when the job needs over 50% more again. Both share the same short-body construction - confirm exact envelope dimensions from the datasheet. Because the piston drifts whenever air is removed, add a rod lock or pilot check valve for any load that must stay held. FB flange, CA/CB clevis, CR and FTC mountings are offered, and the optional -S magnet enables CMSE or DMSE switches in the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X100 FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa push rises to 3518.6 N and pull to 3298.7 N. The theoretical maximum is 512.6 kgf at 1.0 MPa. The cylinder is double acting, so air drives both the extend and return strokes, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Operating range is 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s.
The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with threaded front and back covers for easy service. FB flange, CA/CB clevis, CR and FTC mountings fit the yoke, and the rod end carries a female M12x1.75 thread. Position sensing requires the optional -S magnet code: with it, CMSE or DMSE switches mount in the body slots - without -S there is no magnet and no switch can be read.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.