Airtac TACE Guided Compact Cylinder TACE80X30S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X30S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 30mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke30 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X30S
Double acting and non-rotating, the AirTAC TACE80X30S pairs an 80 mm bore with a 30 mm stroke in a short ISO 21287 compact body. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures climb to 3518.6 N and 3298.7 N, with a theoretical peak of 512.6 kgf at 1.0 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or clamping plate stays square without any external guide.
For sizing, plan on about 1508 N of real work at 0.5 MPa, or expect it to lift roughly 128 kg vertically with a 2:1 margin. The hard-anodized aluminium body with an S45C hard-chrome plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, and a fixed TPU bumper at each end absorbs end-of-stroke energy. Because this is the -S version, the magnet is already fitted, so CMSE / DMSE reed or solid-state switches can be added for end-of-stroke feedback; the 1/4" port and female M12x1.75 rod thread suit heavier tooling.
Airtac TACE Guided Compact Cylinder TACE80X30S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X30S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 30 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X30S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X30S Is Used
Press-fit station for automotive brackets
A 30 mm stroke is enough to seat bushings or dowels in steel brackets, and 2513.3 N at 0.5 MPa covers light staking where a full-length press would never fit between the fixtures.
Clamp on a CNC machining fixture
The twin-guide yoke keeps the clamp plate square on a cast housing while it carries side load, and the short body tucks inside machine guards that leave no room for a longer cylinder.
Vertical part lift in a stamping cell
With about 128 kg of vertical lift capacity at a 2:1 margin, the 80 mm bore raises and lowers stamped panels between the press and the conveyor at 30-500 mm/s.
Is the Airtac TACE Guided Compact Cylinder TACE80X30S the Right Cylinder?
If 2513.3 N at 0.5 MPa is more than the job needs, step down to the 63 mm bore at 1558.6 N; if the load is heavier, the 100 mm bore reaches 3927.0 N under the same pressure. Remember the piston drifts when air is lost - it never locks or brakes - so add a rod lock or pilot check valve where a load must stay held. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and the -S magnet on this model is ready for CMSE / DMSE switches without any rework.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X30S FAQ
At 0.5 MPa the 80 mm bore pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa it pushes 3518.6 N and pulls 3298.7 N; the theoretical maximum is 512.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed range 30-500 mm/s, and air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it fits tight jigs and gantries. A fixed TPU bumper at both ends absorbs end-of-stroke energy. Mounting options are FB flange, CA/CB clevis, CR and FTC. This -S model carries the optional magnet, so CMSE / DMSE switches can be mounted for position signal; the rod end is a female M12x1.75 thread and the port is 1/4".
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.