Airtac TACE Guided Compact Cylinder TACE80X60S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X60S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 60mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X60S
Double acting and non-rotating, the AirTAC TACE80X60S pairs an 80 mm bore with a 60 mm stroke on a twin-guide yoke that stops tooling spin and carries side load. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those rise to 3518.6 N push and 3298.7 N pull, with a theoretical 512.6 kgf at 1.0 MPa. The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight gantries and press fixtures a full-length body cannot fit.
Plan on roughly 1508 N of usable work at 0.5 MPa, about 60% of the push rating; on the vertical-lift math that means this cylinder raises a part of about 128 kg while keeping a 2:1 margin. The hard-anodized aluminium body runs a hard-chrome S45C rod with a female M12x1.75 thread, 1/4" PT ports and fixed TPU bumpers at both ends. Because the -S magnet is fitted on this model, CMSE or DMSE switches mount straight onto the body slots for end-of-stroke signalling.
Airtac TACE Guided Compact Cylinder TACE80X60S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X60S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X60S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X60S Is Used
Weld fixture clamping
Clamps steel brackets in an automotive weld cell: 2513.3 N of push at 0.5 MPa holds the joint, while the twin-guide yoke keeps the clamp pad square to the part without an external guide.
Carton push-off on packaging lines
A 60 mm stroke sweeps cartons off a conveyor into a chute; the fitted -S magnet drives a CMSE switch so the PLC confirms each eject before the next box arrives.
Casting lift-and-lower station
Lifts aluminium housings of about 128 kg vertically in a machining cell with a 2:1 margin, using the short ISO 21287 body to fit inside the machine guard envelope.
Is the Airtac TACE Guided Compact Cylinder TACE80X60S the Right Cylinder?
If 2513.3 N of push at 0.5 MPa is more than the job needs, the bore 63 TACE delivers 1558.6 N at the same pressure; if the load grows, step up to the bore 100 version at 3927.0 N. Remember the piston drifts when air is lost, so a held load calls for a rod lock or a pilot check valve in the line. Mounting options are FB flange, CA/CB clevis, CR and FTC, and this -S model already carries the optional magnet, so CMSE / DMSE switches can be added without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X60S FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N. At 0.7 MPa the push is 3518.6 N and the pull 3298.7 N. The theoretical maximum at 1.0 MPa is 512.6 kgf. Operating pressure spans 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, and speed runs 30-500 mm/s on air filtered to 40 um.
The ISO 21287 build saves about 50% of the mounting length of an ISO 15552 profile cylinder, and fixed TPU bumpers at each end absorb end-of-stroke energy. They do not hold a load: if air is lost the piston drifts, so add a rod lock or pilot check valve where a load must stay put. Mounting choices are FB flange, CA/CB clevis, CR and FTC. This -S version carries the magnet, so CMSE or DMSE reed or solid-state switches clip into the body slots directly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X60S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.