Airtac TACE Guided Compact Cylinder TACE80X80S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X80S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 80mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke80 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X80S
The TACE80X80S is a double acting, non-rotating compact cylinder built to ISO 21287: an 80 mm bore drives a 20 mm hard-chrome-plated S45C rod through an 80 mm stroke, and twin guide rods on a yoke stop the tooling rotating while carrying side load. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures rise to 3518.6 N push and 3298.7 N pull, with a theoretical peak of 512.6 kgf at 1.0 MPa. Supply air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C.
Plan on roughly 1508 N of real work at 0.5 MPa (about 0.6 of the push figure), which lifts about 128 kg vertically with a 2:1 margin. The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight welding gantries and press fixtures where a full-length cylinder will not fit. A fixed TPU bumper at each end absorbs end-of-stroke energy, the -S code on this model carries the magnet for CMSE / DMSE switches, and the 1/4" port plus M12x1.75 female rod thread accept standard fittings.
Airtac TACE Guided Compact Cylinder TACE80X80S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X80S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 80 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X80S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X80S Is Used
Press-fit bushings
The 2513.3 N push at 0.5 MPa presses bronze bushings into aluminium pump housings on an automotive sub-assembly line, with the twin-guide yoke keeping the ram square to the bore.
Vertical part lifting
With about 128 kg of vertical lift capacity at a 2:1 margin, it raises cast gearbox housings between machining stations in an 80 mm lift step.
Welding fixture clamping
In a robotic welding gantry, the non-rotating twin guide rods hold steel brackets square while the 80 mm stroke clamps them against the fixture before the torch passes.
Is the Airtac TACE Guided Compact Cylinder TACE80X80S the Right Cylinder?
If 2513.3 N at 0.5 MPa is more than the job needs, the 63 mm bore still delivers 1558.6 N push; if the load grows, step up to the 100 mm bore at 3927.0 N. This cylinder does not hold position when air is lost - the piston drifts - so fit a rod lock or pilot check valve wherever a load must stay put. Mounting choices are FB flange, CA clevis, CB clevis, CR and FTC, and the -S magnet fitted on this model lets CMSE / DMSE switches report stroke position.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X80S FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa push rises to 3518.6 N and pull to 3298.7 N. The theoretical maximum is 512.6 kgf at 1.0 MPa. For sizing, treat about 1508 N (0.6 of push) as the usable working force, roughly a 128 kg vertical lift with a 2:1 margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium body, S45C hard-chrome rod and fixed TPU bumpers at both ends. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be clamped to the body for end-of-stroke signals. Mounting options are FB flange, CA/CB clevis, CR and FTC.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X80S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.