Airtac TACED Guided Compact Cylinder TACED25X70
The AirTAC Airtac TACED Guided Compact Cylinder TACED25X70 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 70mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke70 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED25X70
A double acting compact cylinder built to ISO 21287, the TACED25X70 pushes a 10 mm rod out of BOTH covers, so its 25 mm bore delivers the same 206.2 N at 0.5 MPa in either direction (288.6 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or fixture plate stays square without an external guide. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs and guarding where a full-length body will not fit.
For sizing, treat roughly 123 N (about 0.6 of the 206.2 N rating) as the usable working force at 0.5 MPa, and expect it to lift about 10 kg vertically once a 2:1 margin is applied. The hard-anodized aluminium body with roller-burnished bore and the S45C hard-chrome plated rod resist wear, a fixed TPU bumper absorbs end-of-stroke shock at both ends, and the female M6x1.0 rod thread on each side plus the M5x0.8 PT port keep plumbing simple. Speed range is 30-500 mm/s over 0.15-1.0 MPa (22-145 psi).
Airtac TACED Guided Compact Cylinder TACED25X70 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED25X70 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED25X70
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED25X70 Is Used
Push-pull jig clamping
The through-rod clamps and releases with identical 206.2 N force at 0.5 MPa, so a drill jig on a CNC line needs no direction-dependent pressure setting.
Centering gripper on an assembly cell
Twin guide rods keep the gripper jaws from rotating while the double rod closes and opens a small housing with equal force both ways.
Reciprocating elevator tray
A 70 mm stroke raises and lowers a light tray of vials about 10 kg vertically with margin, and the TPU bumpers soften both ends of each cycle.
Is the Airtac TACED Guided Compact Cylinder TACED25X70 the Right Cylinder?
At 70 mm stroke this sits mid-range for the 25 mm bore, whose standard strokes run to 100 mm, so no made-to-order build is needed. If 206.2 N per side is marginal, step up to the 32 mm bore for 345.6 N at 0.5 MPa; for lighter pick-and-place the 20 mm bore gives 117.8 N. Remember the piston drifts when air is lost - add a rod lock or pilot check valve if the load must stay put. The -S code adds the magnet for CMSE / DMSE switches; without it no sensor can be fitted. FB flange mounting is available.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED25X70 FAQ
Yes - the double-rod design means both sides see the rod-side area, so output is equal either way: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, with a maximum of 42.0 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 short body (about 50% of the mounting length of an ISO 15552 profile cylinder), hard-anodized aluminium construction, S45C hard-chrome rod, fixed TPU bumpers at both ends, M5x0.8 PT ports and female M6x1.0 threads on both rod ends are standard. The magnet is optional: order the -S code to enable CMSE / DMSE switches, otherwise no sensor can be mounted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED25X70
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.