Airtac TACED Guided Compact Cylinder TACED32X80S
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X80S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X80S
Double acting with a rod leaving both covers, the TACED32X80S pushes and pulls with identical force: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa in each direction, because both sides work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and take side load, so a gripper or plate stays square without an external guide. The 32 mm bore runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this 80 mm stroke version slots into tight jigs, guarding and gantries. A hard-anodized aluminium body carries an S45C hard-chrome rod, and fixed TPU bumpers absorb end-of-stroke energy at both ends. Because the S code is in this model, the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clipped onto the body slots for position feedback. As a planning figure, expect roughly 207 N of usable work at 0.5 MPa, and a vertical lift of about 17 kg with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED32X80S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X80S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X80S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X80S Is Used
Symmetric fixture clamping
A through-rod clamps a machined housing from both sides with the same 345.6 N, so the fixture grips evenly without tuning two separate cylinders.
Pusher on a packaging line
The 80 mm stroke kicks cartons off a conveyor at up to 500 mm/s, and the twin guide rods keep the pusher plate square to the belt.
Gated assembly station
With the -S magnet fitted, CMSE / DMSE switches confirm extend and retract positions inside a guard where the short body is the only cylinder that fits.
Is the Airtac TACED Guided Compact Cylinder TACED32X80S the Right Cylinder?
At 345.6 N per direction, this bore sits between the 25 mm (206.2 N) and 40 mm (571.8 N) double-rod units - step down for lighter pick-and-place, up if the 80 mm stroke must carry heavier tooling. The piston drifts when air is lost, so add a rod lock or pilot check valve if the load must stay put. FB flange mounting is available, and the fitted -S magnet means CMSE / DMSE switching works out of the box.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X80S FAQ
Yes - it is a double-rod cylinder, so force is equal in extend and retract: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa in both directions (rod-side area). At 1.0 MPa the peak is 70.5 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, on air filtered to 40 um, at 30-500 mm/s and -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, ideal for tight gantries. This model carries the optional -S magnet, so CMSE / DMSE switches mount in the body slots; FB flange mounting is offered, and fixed TPU bumpers absorb end-of-stroke shock. The rod end is female M8x1.25 with a 1/8" PT port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X80S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.