Airtac TACED Guided Compact Cylinder TACED40X35
The AirTAC Airtac TACED Guided Compact Cylinder TACED40X35 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø40mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ40 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED40X35
Double acting with a rod leaving both covers, the TACED40X35 delivers 571.8 N in each direction at 0.5 MPa (800.5 N at 0.7 MPa) because both strokes work on the rod-side area. The twin guide rods on the yoke stop tooling from rotating and carry side load, so a gripper or press plate stays square without an external guide. Its ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs and guarding where a full-length body cannot fit.
Practically, plan for roughly 343 N of real work at 0.5 MPa and expect about 29 kg of vertical lift at a 2:1 margin. The 40 mm bore takes a 12 mm hard-chrome-plated S45C rod with an M8x1.25 female thread, fed through 1/8" ports, and runs 30-500 mm/s on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi). A fixed TPU bumper absorbs end-of-stroke energy at both covers, and the optional -S magnet enables CMSE / DMSE switches.
Airtac TACED Guided Compact Cylinder TACED40X35 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED40X35 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED40X35
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 40 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED40X35 Is Used
CNC fixture clamping
The 571.8 N both-ways force clamps and releases a machined housing with equal push, and the twin guide rods keep the clamp pad square to the datum.
Push-pull tray transfer
A rod on each cover means one cylinder both ejects and retracts a tray on a packaging line, with 343 N of usable work at 0.5 MPa in each stroke.
Small press fitting
Pressing bushings into brackets needs about 29 kg of controlled vertical force - the 40 mm bore delivers it in a body about half the length of an ISO 15552 profile cylinder.
Is the Airtac TACED Guided Compact Cylinder TACED40X35 the Right Cylinder?
At 571.8 N per side, the 40 mm bore sits between the 32 mm (345.6 N) and 50 mm (881.2 N) classes, so pick 32 mm for lighter clamping and 50 mm when the load climbs past about 570 N. The 35 mm stroke is well inside the 200 mm maximum standard stroke for this bore. Remember the piston drifts if air is lost - add a rod lock or pilot check valve when a load must be held. Order the -S code if CMSE / DMSE sensing is needed, and FB flange mounting if the yoke alone will not carry the fixture.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED40X35 FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so output is equal both ways: 571.8 N at 0.5 MPa, 800.5 N at 0.7 MPa, and up to 116.6 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with a fixed TPU bumper at each end.
The hard-anodized aluminium ISO 21287 body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, with a 12 mm hard-chrome S45C rod, M8x1.25 female thread and 1/8" ports. Sensing requires the optional -S magnet code - without it no CMSE / DMSE switch can be mounted. FB flange mounting is available, and the maximum standard stroke for this bore is 200 mm.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED40X35
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.