Airtac TACED Guided Compact Cylinder TACED50X60S
The AirTAC TACED Guided Compact Cylinder TACED50X60S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 60mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X60S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED50X60S pushes a 16 mm rod out of both covers, so the 50 mm bore delivers the same 881.2 N at 0.5 MPa (1233.7 N at 0.7 MPa) whether it extends or retracts. Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide. The hard-anodized aluminium body with an S45C hard-chrome plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight welding jigs and machine frames. The S in the model code means the magnet is fitted, so CMSE / DMSE switches can be clamped straight onto the body slot. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the female M10x1.5 rod thread on both ends suits yoke-mounted tooling.
Airtac TACED Guided Compact Cylinder TACED50X60S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X60S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X60S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X60S Is Used
Clamping welding fixtures
The 881.2 N clamping force in both directions and non-rotating twin guide yoke hold a car-panel jig square through thousands of clamp-and-release cycles, and the short body fits inside the fixture frame.
Pick-and-place gripper drive
A 45 kg vertical lift capability with equal force closing and opening suits a robotic gripper handling aluminium castings, with CMSE switches on the fitted magnet confirming grip position.
Benchtop press station
Pushing 1233.7 N at 0.7 MPa through a 60 mm stroke gives a compact manual-load press for pressing bushings into small housings where a full-length profile cylinder will not fit.
Is the Airtac TACED Guided Compact Cylinder TACED50X60S the Right Cylinder?
At 881.2 N per direction, this 50 mm bore sits between the 40 mm TACED (571.8 N at 0.5 MPa) and the 63 mm TACED (1458.1 N at 0.5 MPa) - step down if your load is under 550 N, step up if you need over 900 N of repeatable force. Remember the piston drifts when air is lost, so add a rod lock or pilot check valve if a load must stay held. The 60 mm stroke is within the standard range for this bore, the 1/8" ports take PT fittings as coded, and FB flange, CA, CB, CR or FTC mounts can be selected at order time.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X60S FAQ
Yes - the double-rod design means a rod exits both covers and both sides work on the rod-side area, so output is equal either way: 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa, with a maximum of 179.7 kgf at 1.0 MPa. The twin guide rods keep the load non-rotating throughout the 60 mm stroke.
The S code means the optional -S magnet is fitted on this unit, so CMSE or DMSE reed or solid-state switches mount directly in the body slots; models ordered without the S code carry no magnet. The ISO 21287 compact body is hard-anodized aluminium about 50% shorter in mounting length than an ISO 15552 profile cylinder, with a fixed TPU bumper at each end and 1/8" PT ports.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X60S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.