Airtac TACED Guided Compact Cylinder TACED50X80S
The AirTAC TACED Guided Compact Cylinder TACED50X80S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X80S
This is a double acting, double rod ISO 21287 compact cylinder: a rod exits both covers, so the 50 mm bore delivers 881.2 N at 0.5 MPa in EITHER direction, because both sides see the rod-side area. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide - a real edge over a plain compact cylinder. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted anywhere along the body slots.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries where a full-length cylinder will not. A hard-anodized aluminium body with a roller-burnished bore runs against an S45C hard-chrome plated rod, and a fixed TPU bumper at each end absorbs end-of-stroke energy.
Airtac TACED Guided Compact Cylinder TACED50X80S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X80S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X80S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X80S Is Used
Fixture clamping on a CNC machining center
The 881.2 N clamping force holds a machined aluminum bracket square in a drill jig, and the twin guide yoke keeps the clamp pad from twisting as it closes.
Pusher on a bottling line conveyor
Equal 881.2 N force in both directions lets one cylinder push cartons off the belt and retract with the same power, while the 80 mm stroke clears the lane.
Sample press in a lab automation cell
The compact body fits under a low gantry where an ISO 15552 profile cylinder would not, and CMSE switches on the fitted magnet confirm each press cycle.
Is the Airtac TACED Guided Compact Cylinder TACED50X80S the Right Cylinder?
At 881.2 N per direction at 0.5 MPa, the 50 mm bore suits medium clamping and press-fit work; step down to the 32 mm bore (345.6 N) for lighter tooling or up to the 63 mm bore (1458.1 N) when the part fights back. The 80 mm stroke sits well inside the 250 mm maximum standard stroke for this bore, so it is a catalog item, not a made-to-order build. Remember it does not hold position when air is lost - the piston drifts - so add a rod lock or pilot check valve if the load must stay put. FB flange mounting is available, and the fitted -S magnet lets you add CMSE / DMSE switches for end-of-stroke or mid-stroke detection.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X80S FAQ
Yes - the double rod design means a rod exits both covers, so both strokes see the rod-side area. At 0.5 MPa it delivers 881.2 N either way; at 0.7 MPa it delivers 1233.7 N either way; the maximum at 1.0 MPa is 179.7 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed runs 30-500 mm/s.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end to absorb end-of-stroke energy. The -S code on this model means the magnet is fitted, so CMSE / DMSE switches can be slid into the body slots for position sensing. FB flange mounting is offered, and the rod end carries an M10x1.5 female thread with a 1/8" air port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X80S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.