Airtac TACED Guided Compact Cylinder TACED50X90
The AirTAC TACED Guided Compact Cylinder TACED50X90 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X90
The TACED50X90 is a double acting, double-rod ISO 21287 compact cylinder: a 16 mm rod exits both covers of the 50 mm bore body, so thrust is identical on extend and retract - 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa in either direction. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight fixtures a full-length body cannot reach.
The hard-anodized aluminium body with a roller-burnished bore runs against an S45C hard-chrome plated rod, a two-way piston seal stores grease, and fixed TPU bumpers absorb end-of-stroke energy at both covers. Speed range is 30-500 mm/s over 0.15-1.0 MPa (22-145 psi) of clean, 40 um filtered air.
Airtac TACED Guided Compact Cylinder TACED50X90 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X90 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X90
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X90 Is Used
Fixture clamping on CNC machining centers
Equal 881.2 N clamp and release force in both directions lets one TACED50X90 load and unload aluminum housings in a 90 mm stroke fixture, with the twin guide yoke keeping the clamp pad square to the datum.
Push-off stations on packaging lines
A through-rod pusher on a carton conveyor gets the same 1233.7 N at 0.7 MPa whichever way it fires, and the non-rotating yoke keeps the pusher plate tracking straight across the belt.
Test rig actuation for electronics assemblies
Symmetric rod-side force gives repeatable 881.2 N press and pull cycles on connector fatigue rigs, while the compact body fits inside the guard envelope of the test bench.
Is the Airtac TACED Guided Compact Cylinder TACED50X90 the Right Cylinder?
At 90 mm stroke this bore 50 unit delivers 881.2 N both ways at 0.5 MPa - step down to a TACED32X90 (345.6 N) for lighter clamping, or up to a TACED63X90 (1458.1 N) when the load grows. If the job only needs force on extend, a single-rod TACE saves cost; if rotation does not matter, the plain ACED double rod is the simpler pick. Remember the piston drifts when air is lost, so add a rod lock or pilot check valve for a held load. The rod end is female M10x1.5 and the port is 1/8" PT; FB flange, CA, CB, CR and FTC mountings are available, and only the -S code adds the magnet that lets CMSE / DMSE switches sense position - this model has no magnet fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X90 FAQ
Yes - because a rod exits both covers, both strokes use the rod-side area of the 50 mm bore: 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa, equal on extend and retract. At 1.0 MPa the peak is 179.7 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 90 mm stroke is within the standard range for this bore.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, threaded aluminium covers, an S45C hard-chrome rod and fixed TPU bumpers at both ends - the short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. Position sensing requires the optional -S magnet code, which enables CMSE / DMSE switches; this model has no magnet, so no sensor can be mounted as supplied.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X90
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.