Airtac TACED Guided Compact Cylinder TACED63X25S
The AirTAC TACED Guided Compact Cylinder TACED63X25S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 25mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke25 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X25S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED63X25S pushes a 63 mm bore through a 25 mm stroke with a rod exiting both covers. Because both sides see the rod-side area, output is equal in each direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. Twin guide rods on the yoke stop tooling rotation and carry side load, so a gripper or press plate stays square without an external guide. The fitted -S magnet accepts CMSE / DMSE reed or solid-state switches for end-of-stroke signalling.
The hard-anodized aluminium body with a roller-burnished bore and an S45C hard-chrome plated rod shrugs off wear in high-cycle service, while fixed TPU bumpers at both ends absorb end-of-stroke shock. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and fixtures where a full-length body will not fit.
Airtac TACED Guided Compact Cylinder TACED63X25S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X25S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X25S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X25S Is Used
Fixture clamping on CNC machining centres
The equal 1458.1 N force in both directions clamps and releases a fixture plate with identical grip, and the 25 mm stroke suits quick-change pallet clamps.
Pneumatic gripper for stamped steel parts
Twin guide rods keep the gripper jaws from rotating and carry side load, holding a stamped bracket square through thousands of pick-and-place cycles.
Crimp and mark station on an electronics line
The short ISO 21287 body fits inside a compact crimp head, and the fitted -S magnet with a DMSE switch confirms each 25 mm stroke is complete.
Is the Airtac TACED Guided Compact Cylinder TACED63X25S the Right Cylinder?
At 63 mm bore this model sits mid-range in the TACED family: the 50 mm bore delivers 881.2 N at 0.5 MPa, while the 80 mm bore reaches 2356.2 N, so step up if your press or clamp needs more than about 1458 N. Remember it does not hold position when air is lost - the piston drifts - so add a rod lock or pilot check valve for a held load. The female M10x1.5 rod thread suits most tooling studs, and the fitted -S magnet means CMSE / DMSE switches can be added straight away.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X25S FAQ
Force is equal in both directions because a rod exits both covers and both sides see the rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is 1/8" (PT).
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight jigs and slides. Fixed TPU bumpers at both ends absorb end-of-stroke energy. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches mount in the body slots for position feedback. FB flange mounting is available, and the female rod thread is M10x1.5.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.