Airtac TACED Guided Compact Cylinder TACED63X30S
The AirTAC TACED Guided Compact Cylinder TACED63X30S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 30mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke30 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X30S
Double acting with a rod leaving both covers, the TACED63X30S pushes and pulls with identical force because each side works on the same rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clipped onto the body for end-of-stroke signalling.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this 63 mm unit drops into tight jigs and guarding where a full-length body will not. Hard-anodized aluminium body, S45C hard-chrome plated rod, and a fixed TPU bumper at each end round out the build.
Airtac TACED Guided Compact Cylinder TACED63X30S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X30S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X30S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X30S Is Used
Fixture clamping with position signal
A machining fixture needs 1458.1 N of clamp force applied from either side of the jig. The through-rod lets the clamp close from one cover while the switch-ready magnet confirms the clamped position via a CMSE sensor.
Push-pull transfer on a packaging line
A carton pusher on a wrapping machine strokes 30 mm and must push and eject with equal force. The double rod delivers 2041.3 N at 0.7 MPa in both directions, and the twin guides keep the pusher pad from twisting.
Vertical press assist in electronics assembly
A small press head seating connectors needs steady downward force with no rotation.
Is the Airtac TACED Guided Compact Cylinder TACED63X30S the Right Cylinder?
At 1458.1 N per direction, bore 63 sits mid-range: step down to TACED50 (881.2 N at 0.5 MPa) for lighter clamping, or up to TACED80 (2356.2 N) when the load grows. If you do not need a rod at both covers, TACE gives the same non-rotating guide yoke with a single rod, and ACED offers a plain double rod without the guides. This model carries the optional -S magnet, so position feedback with CMSE / DMSE switches is ready to go. Remember the piston drifts if air is lost - add a rod lock or pilot check valve where a load must be held. FB flange mounting is available; air is 0.15-1.0 MPa (22-145 psi) filtered to 40 um, speed 30-500 mm/s, and the 1/8" port is fixed by the bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X30S FAQ
Yes - the double-rod design means a rod exits both covers, so both strokes work on the rod-side area. Output is 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, equal both ways, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is 1/8" with a female M10x1.5 rod thread.
The compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow jigs and guarded stations. The TPU bumper at each end absorbs end-of-stroke impact but does not lock or hold a load - use a rod lock or pilot check valve for that. Because this model carries the -S magnet, CMSE / DMSE reed or solid-state switches mount directly on the body slots; FB flange mounting is also available.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.