Airtac TACED Guided Compact Cylinder TACED63X5S
The AirTAC TACED Guided Compact Cylinder TACED63X5S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 5mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke5 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X5S
A double acting, double-rod ISO 21287 compact cylinder, the TACED63X5S pushes a 63 mm bore through a very short 5 mm stroke with a rod leaving both covers. Because both sides see the rod-side area, output is identical in each direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a plate or gripper stays square without any external guide.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, with a fixed TPU bumper at each end. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and the fitted -S magnet accepts CMSE / DMSE switches for end-of-stroke sensing on this 5 mm travel.
Airtac TACED Guided Compact Cylinder TACED63X5S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X5S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 5 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X5S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X5S Is Used
CNC fixture clamping
The 1458.1 N symmetric clamp squares a machined housing in a 5 mm clamp-and-release pocket where a full-length cylinder cannot fit.
Press head indexing
Twin guide rods keep a small stamping or marking head from rotating over the 5 mm throw, holding it square to the die without an external guide.
Gated assembly check
With the fitted -S magnet driving a CMSE or DMSE switch, the 5 mm stroke confirms a cover is fully seated on an electronics assembly line.
Is the Airtac TACED Guided Compact Cylinder TACED63X5S the Right Cylinder?
At 1458.1 N per side at 0.5 MPa, this bore sits above the 50 mm frame (881.2 N) and below the 80 mm frame (2356.2 N), so step down for lighter clamps or up for heavier presses. The 5 mm stroke suits short-throw positioning rather than long transfer moves; longer standard strokes exist for this bore if the job changes. Air loss means the piston drifts, so add a rod lock or pilot check valve where a load must be held. This model carries the optional -S magnet, mounts on an FB flange, and uses a female M10x1.5 rod thread with a PT port thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X5S FAQ
Yes. The double-rod design exposes the rod-side area on both sides, so output is equal each way: 1458.1 N at 0.5 MPa, 2041.3 N at 0.7 MPa, with a peak of 297.4 kgf at 1.0 MPa. It is double acting, runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, and the 63 mm bore takes a 1/8" port with an M10x1.5 female rod thread.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so the 5 mm stroke fits tight jigs and gantries. This model includes the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be clamped anywhere along the body for position signals. A fixed TPU bumper decelerates the piston at each end, and the FB flange gives a rigid mounting face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X5S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.