Airtac TACED Guided Compact Cylinder TACED63X75
The AirTAC Airtac TACED Guided Compact Cylinder TACED63X75 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X75
Double acting and double rod, the TACED63X75 pushes a rod out of both covers so the 63 mm bore delivers the same 1458.1 N in each direction at 0.5 MPa (2041.3 N at 0.7 MPa), because both sides work on the rod-side area. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The fixed TPU bumper at each end absorbs end-of-stroke energy.
The body is a hard-anodized aluminium compact build to ISO 21287, about 50% shorter in mounting length than an ISO 15552 profile cylinder, which lets it drop into tight jigs and gantries. Practically, plan on roughly 875 N (about 89 kg) of usable work at 0.5 MPa, and for a vertical lift with a 2:1 margin expect about 74 kg. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and the rod ends in a female M10x1.5 thread.
Airtac TACED Guided Compact Cylinder TACED63X75 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X75 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X75
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X75 Is Used
CNC fixture clamping
The equal 1458.1 N both ways clamps and releases a machined housing in a machining-centre fixture with the same force, and the twin guide yoke keeps the clamp pad square to the datum.
Pallet gripper on a robot cell
A through-rod yoke grips transfer pallets in an automotive assembly cell; the non-rotating twin guide rods hold jaw alignment and carry the side load without extra rails.
Bench press for bushing insertion
With about 875 N of usable work at 0.5 MPa, the short ISO 21287 body presses small bushings into pump housings on a compact bench where a full-length profile cylinder will not fit.
Is the Airtac TACED Guided Compact Cylinder TACED63X75 the Right Cylinder?
At 63 mm bore this sits between the 50 mm (881.2 N at 0.5 MPa) and the 80 mm (2356.2 N at 0.5 MPa) frames; step down for lighter clamping or up if you need over 2000 N. The 75 mm stroke is within the 250 mm standard range for this bore, so no made-to-order build is needed. Remember the piston drifts if air is lost - add a rod lock or pilot check valve where a load must stay held. Order the -S code if you want the magnet for CMSE / DMSE switches; without it no sensor can be fitted. FB flange mounting and G ports are available options.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X75 FAQ
Yes - the double-rod design means a rod exits both covers and both strokes work on the rod-side area, so output is equal each way: 1458.1 N at 0.5 MPa, 2041.3 N at 0.7 MPa, and a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, and the 16 mm hard-chrome rod ends in a female M10x1.5 thread.
The ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it suits tight jigs and gantries. Sensors are possible only if you order the optional -S magnet code, which allows CMSE / DMSE reed or solid-state switches on the body slots; the standard TACED63X75 has no magnet fitted. FB flange mounting is available, and the fixed TPU bumper at each end absorbs end-of-stroke impact.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.