Airtac TACED Guided Compact Cylinder TACED63X90
The AirTAC Airtac TACED Guided Compact Cylinder TACED63X90 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X90
Double acting with a through rod that exits both covers, the TACED63X90 delivers 1458.1 N in each direction at 0.5 MPa (2041.3 N at 0.7 MPa), because both strokes work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The 63 mm bore tops out at 297.4 kgf, enough for heavy clamping and lift-and-place work.
This is an ISO 21287 compact build: the hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and fixture plates. The S45C hard-chrome rod runs in a roller-burnished bore, a fixed TPU bumper decelerates each end of the 90 mm stroke, and speed spans 30-500 mm/s at 0.15-1.0 MPa (22-145 psi). As a rule of thumb, plan for about 875 N of real work at 0.5 MPa, which lifts roughly 44 kg vertically with a 2:1 margin. Note that the piston drifts if air is lost, so add a rod lock or pilot check valve for held loads.
Airtac TACED Guided Compact Cylinder TACED63X90 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X90 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X90
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X90 Is Used
CNC fixture clamping
The equal 1458.1 N force both ways clamps and releases machined aluminium housings with identical grip, while the twin guide yoke keeps the clamp pad square to the fixture.
Palletizing push-station
A 90 mm stroke pushes cartons onto a pallet lane at up to 500 mm/s, and the compact body fits the tight envelope beside the conveyor frame where a full-length profile cylinder will not.
Pick-and-place lift head
With about 44 kg of vertical lift capacity at a 2:1 margin, the double rod raises and lowers a vacuum plate on a packaging gantry, the twin guide rods stopping the head from twisting.
Is the Airtac TACED Guided Compact Cylinder TACED63X90 the Right Cylinder?
At 1458.1 N per side, bore 63 sits between bore 50 (881.2 N) and bore 80 (2356.2 N) at 0.5 MPa, so choose down if your load is under 60 kg and up for presses above 200 kg. The 90 mm stroke is within the 250 mm standard range for this bore. Order the -S code if you want the optional magnet for CMSE / DMSE switches; without it no sensor can be mounted. FB flange mounting is available, and the rod end carries a female M10x1.5 thread with a PT 1/8" port.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X90 FAQ
Yes. Because a rod exits both covers, both strokes work on the rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, equal push and pull. Maximum force at 1.0 MPa is 297.4 kgf. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The ISO 21287 aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow guards and fixture plates. The twin guide rods on the yoke resist rotation and side load, and a fixed TPU bumper decelerates each end of the stroke. FB flange mounting and the optional -S magnet for CMSE / DMSE switches are order choices; the rod end is female M10x1.5 and the port is 1/8" PT.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X90
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.