Airtac TACED Guided Compact Cylinder TACED80X100
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X100 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 100mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke100 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X100
A double acting, double-rod ISO 21287 compact cylinder, the TACED80X100 pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an identical 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) in each direction - the rod-side area is the same on both faces. Twin guide rods on the yoke stop the tooling rotating and take side load, so a press plate or gripper stays square without an external guide. The hard-anodized aluminium body carries a fixed TPU bumper at each end, and the female M12x1.75 rod thread suits standard rod accessories.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this bore size fits heavy jigs and gantries where a full-length body will not. For planning, treat roughly 0.6 of the 0.5 MPa force as usable work - about 1414 N, or near 144 kg of horizontal push with margin. Held vertically with a 2:1 margin it lifts about 120 kg. Air is filtered to 40 um, pressure runs 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, temperature -20 to +70 C. Note this cylinder drifts when air is lost - add a rod lock or pilot check valve to hold a load.
Airtac TACED Guided Compact Cylinder TACED80X100 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X100 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X100
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X100 Is Used
Twin-sided press fixture
The through-rod lets a machining cell clamp a casting from both sides with one cylinder, delivering 2356.2 N in each direction at 0.5 MPa while the twin guide rods keep the pressure plate square.
Gantry pick-and-place head
With about 120 kg of vertical lift at a 2:1 margin, the 80 mm bore handles steel bracket transfer on an automotive gantry, and the short body fits the tight Z-axis envelope.
Balanced stamping ejector
Equal force both ways makes this cylinder a natural ejector under a stamping die - the return stroke is as strong as the strike, with the TPU bumper softening both ends of the 100 mm travel.
Is the Airtac TACED Guided Compact Cylinder TACED80X100 the Right Cylinder?
At 2356.2 N per direction at 0.5 MPa, the 80 mm bore sits between the 63 mm (1458.1 N) and the 100 mm (3769.9 N) - step down for lighter clamping, up for heavy press work. If your stroke stays within the standard range for this bore you avoid made-to-order lead times. Choose the -S code if you need CMSE / DMSE switches; this model has no magnet fitted, so no sensor can be mounted as-is. FB flange mounting is available, and the rod end is female M12x1.75 with a PT port.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X100 FAQ
Yes - the double-rod design means both sides of the piston see the rod-side area, so output is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), and speed range 30-500 mm/s.
This version has no magnet, so position switches cannot be fitted - order the TACED80X100S to enable CMSE or DMSE reed / solid-state switches on the magnet slots around the body. The port is 1/4" (PT thread), the rod end is female M12x1.75, and FB flange mounting is offered. Outline dimensions are not listed here - confirm from datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.