Airtac TACED Guided Compact Cylinder TACED80X100S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X100S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 100mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke100 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X100S
Double acting and double rod, the AirTAC TACED80X100S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an equal 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The fixed TPU bumper at each end absorbs end-of-stroke energy, and speed spans 30-500 mm/s.
The hard-anodized aluminium body is an ISO 21287 compact build, saving about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight gantries and guarding. This -S model carries the optional magnet, so CMSE / DMSE reed or solid-state switches can be mounted for end-of-stroke signals. Running 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, it suits air filtered to 40 um from -20 to +70 C. For planning, treat roughly 1414 N (about 144 kg of force) as the usable working output at 0.5 MPa.
Airtac TACED Guided Compact Cylinder TACED80X100S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X100S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X100S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X100S Is Used
Clamping on a CNC fixture
The twin guide yoke keeps the clamp plate square over a 100 mm stroke, with 2356.2 N holding a machined housing against the stop in either direction.
Pallet strapper tensioner
Equal push and pull from the double rod tensions and releases the strap at the same force, and the -S magnet feeds end-of-stroke signals to the PLC via a DMSE switch.
Stamping mark press
About 1414 N of usable working force at 0.5 MPa stamps batch codes into aluminium castings, while the compact body fits the shallow press head.
Is the Airtac TACED Guided Compact Cylinder TACED80X100S the Right Cylinder?
At 2356.2 N per direction at 0.5 MPa, the 80 mm bore sits well above the 63 mm size (1458.1 N) and below the 100 mm bore (3769.9 N), so step down if the load is lighter or up if you need more. The through-rod gives equal force both ways, handy for push-pull fixtures. Remember it drifts when air is lost - add a rod lock or pilot check valve if the load must stay held. The female M12x1.75 rod thread and 1/4" PT ports suit standard fittings, and the fitted -S magnet means CMSE / DMSE switches work out of the box.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X100S FAQ
Yes - the double-rod design means a rod exits both covers, so both sides see the rod-side area. Output is 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, equal in push and pull, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s.
The ISO 21287 aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, so it fits shallow machine frames. A fixed TPU bumper at each end decelerates the piston at stroke ends; it is not adjustable and never locks the load, so use a rod lock or pilot check valve for holding. The fitted -S magnet allows CMSE / DMSE switch mounting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.