Airtac TACED Guided Compact Cylinder TACED80X10S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X10S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 10mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke10 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X10S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED80X10S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an identical 2356.2 N at 0.5 MPa in each direction (3298.7 N at 0.7 MPa). Twin guide rods on the yoke stop tooling rotation and carry side load, keeping a gripper or press plate square without any external guide. The hard-anodized aluminium body pairs with an S45C hard-chrome plated rod, and a fixed TPU bumper at each end absorbs end-of-stroke shock.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight welding fixtures and press gantries where a full-length body will not fit. With the -S magnet this model carries, CMSE or DMSE reed and solid-state switches can be mounted anywhere along the body slots. Plan on roughly 1414 N of usable work at 0.5 MPa, which is about 72 kg of vertical lift with a 2:1 margin - enough for clamping or lifting a heavy aluminium die segment.
Airtac TACED Guided Compact Cylinder TACED80X10S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X10S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X10S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X10S Is Used
Press-fit die clamping
The 10 mm stroke and 2356.2 N per side at 0.5 MPa clamp an aluminium die segment in a stamping fixture, with twin guide rods keeping the clamp plate square on the die face.
Weld fixture part location
A short-throw through-rod locates a steel bracket from both sides of a robotic weld jig; the compact body fits where an ISO 15552 profile cylinder is too long.
Battery tray lift assist
With about 72 kg of vertical lift at a 2:1 margin, the cylinder raises a forklift battery tray in a test rig, guided non-rotating by the twin yoke rods.
Is the Airtac TACED Guided Compact Cylinder TACED80X10S the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, the 80 mm bore sits above the 63 mm (1458.1 N) and below the 100 mm (3769.9 N) - choose 63 mm if your load is under 850 N of work, step to 100 mm for heavy stamping tools. The 10 mm stroke suits short-throw clamping; longer standard strokes run to 100 mm for this bore. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve for a held load. FB flange mounting and the optional -S magnet for CMSE / DMSE switches can be matched to your fixture.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X10S FAQ
Yes - the double-rod design exposes the rod-side area on both sides, so force is equal each way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" port serves both ends of the 80 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so the 80 mm bore fits shallow fixtures and guarded cells. This model carries the optional -S magnet, so CMSE or DMSE reed or solid-state switches can be slid into the body slots for end-of-stroke signalling, and the fixed TPU bumpers at both ends soften the 10 mm travel.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.