Airtac TACED Guided Compact Cylinder TACED80X25S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X25S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 25mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke25 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X25S
A double acting, double rod ISO 21287 compact cylinder, the TACED80X25S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an equal 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa) because both sides work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without any external guide. The hard-anodized aluminium body with an S45C hard-chrome plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight welding fixtures and gantry stations where a full-length body will not fit. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches mount directly in the body slots. As a rule of thumb, plan on roughly 1414 N of usable work at 0.5 MPa; vertically that is about 240 kgf, so with a 2:1 margin it lifts about 120 kg.
Airtac TACED Guided Compact Cylinder TACED80X25S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X25S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X25S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X25S Is Used
Welding fixture clamping
The twin guide yoke keeps a clamp shoe square on a car-body jig while the 80 mm bore delivers 2356.2 N in both directions, and the 25 mm stroke suits shallow clamp-and-release moves.
Press-fit station
Pushing bearings into housings on an assembly line: about 1414 N of usable force at 0.5 MPa, with the short compact body fitting under a low press frame where a profile cylinder cannot.
Pallet divert on a conveyor
The through-rod pushes a divert plate out and pulls it back with equal force, and the fitted -S magnet feeds CMSE / DMSE switch signals to the PLC for end-of-stroke confirmation.
Is the Airtac TACED Guided Compact Cylinder TACED80X25S the Right Cylinder?
At 80 mm bore this is the second-strongest TACED size: 2356.2 N both ways at 0.5 MPa. Step down to the 63 mm bore (1458.1 N) for lighter clamping, or up to the 100 mm bore (3769.9 N) when the load demands more. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must stay held. The 25 mm stroke sits well inside the standard range for this bore, and FB flange mounting plus the fitted -S magnet (CMSE / DMSE switching) make it easy to drop into an existing station.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X25S FAQ
Yes. Because a rod exits both covers, both sides see the rod-side area, so output is equal either way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" port depends only on the 80 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures and guarded gantries. The twin guide rods stop the load rotating and take side load without an external guide, a fixed TPU bumper absorbs end-of-stroke shock at both ends, and this -S model carries the optional magnet so CMSE / DMSE switches can be mounted in the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.