Airtac TACED Guided Compact Cylinder TACED80X30S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X30S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 30mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke30 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X30S
Double acting with a rod exiting both covers, the TACED80X30S delivers 2356.2 N in either direction at 0.5 MPa (3298.7 N at 0.7 MPa) because both strokes work on the rod-side area. The 80 mm bore drives a 20 mm rod through a 30 mm stroke, with a fixed TPU bumper at each end absorbing end-of-stroke energy. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide.
The hard-anodized aluminium body is a short ISO 21287 compact build that saves about 50% of the mounting length of an ISO 15552 profile cylinder, letting it slot into tight machine frames and gantries. The S code on this model means the optional magnet is fitted, so CMSE or DMSE reed and solid-state switches can be mounted anywhere along the body slots. Air supply is filtered to 40 um, pressure runs 0.15-1.0 MPa (22-145 psi), and speed spans 30-500 mm/s.
Airtac TACED Guided Compact Cylinder TACED80X30S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X30S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X30S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X30S Is Used
Clamping weld fixtures
The 2356.2 N through-rod clamps steel brackets from both sides of a robotic weld cell, and the twin guide yoke keeps the clamp pads square to the part.
Stamping press ejector
A 30 mm stroke ejects finished stamped washers from the die on the return stroke too, since both directions push the full 2356.2 N at 0.5 MPa.
Case pusher on packaging lines
Pushes cartons off a conveyor at up to 500 mm/s; the -S magnet with a DMSE switch confirms the pusher has fully retracted each cycle.
Is the Airtac TACED Guided Compact Cylinder TACED80X30S the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, plan on roughly 1410 N of real work, which is about 143 kg of vertical lift with a 2:1 margin. If your load needs less, the TACED63X30S gives 1458.1 N both ways; if it needs more, step up to the TACED100X30S at 3769.9 N. Remember the piston drifts when air is lost, so add a rod lock or pilot check valve for a held load. This model carries the optional -S magnet for CMSE / DMSE switches, uses a female M12x1.75 rod thread with 1/4" PT ports, and mounts via the FB flange option.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X30S FAQ
Because a rod exits both covers, force is equal in both directions: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa on the rod-side area. Maximum force at 1.0 MPa is 480.5 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, and speed runs 30-500 mm/s.
The hard-anodized aluminium body is an ISO 21287 compact build, roughly 50% shorter in mounting length than an ISO 15552 profile cylinder, so it fits shallow machine frames. A fixed TPU pad at each end decelerates the piston at stroke ends; it is not adjustable and does not hold a load, so use a rod lock or pilot check valve where position must be kept. The fitted -S magnet allows CMSE / DMSE switch mounting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.