Airtac TACED Guided Compact Cylinder TACED80X35S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X35S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 35mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke35 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X35S
Double acting and double rod, the TACED80X35S pushes with an identical 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa), because a rod exits both covers and both sides work on the rod-side area. The 80 mm bore drives a 20 mm rod over a 35 mm stroke at 30-500 mm/s, with a fixed TPU bumper at each end absorbing the stop. Its ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into presses and fixtures where a full-length body will not fit.
Twin guide rods on the yoke stop the tooling rotating and carry side load, so a press plate or gripper stays square without an external guide. The hard-anodized aluminium body pairs with an S45C hard-chrome-plated rod, and the -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted for end-of-stroke signalling. As a rule of thumb, plan on roughly 1414 N (about 144 kg) of real work at 0.5 MPa, or lift about 120 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED80X35S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X35S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X35S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X35S Is Used
Short-stroke press station
The 35 mm stroke and 2356.2 N both-ways force suit a benchtop crimping or marking press where the compact body fits under a low gantry.
Reciprocating transfer plate
A rod exits each cover, so one cylinder can push a pallet carrier forward and pull it back with equal 2356.2 N force, no rotation thanks to the twin guide rods.
Position-monitored clamp
With the fitted -S magnet, CMSE / DMSE switches confirm open and closed positions on a fixture clamp in an automotive welding cell.
Is the Airtac TACED Guided Compact Cylinder TACED80X35S the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, the 80 mm bore sits between the 63 mm (1458.1 N) and 100 mm (3769.9 N) choices; step down to 63 mm for lighter clamping, up to 100 mm for heavy stamping. Note that it does not hold position if air is lost - the piston drifts - so add a rod lock or pilot check valve for a held load. FB flange mounting is available, the rod end is female M12x1.75, and the fitted -S magnet lets you add CMSE / DMSE switches without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X35S FAQ
Yes - the double-rod design means output is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa on the rod-side area, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures and guarded cells. The twin guide rods on the yoke stop tooling rotation and carry side load, and a fixed TPU bumper at each end absorbs the stop. This model carries the optional -S magnet, so CMSE / DMSE switches can be fitted; the female rod thread is M12x1.75 and the port is 1/4" PT.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.