Airtac TACED Guided Compact Cylinder TACED80X60S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X60S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 60mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X60S
Double acting with a rod leaving both covers, the TACED80X60S pushes and pulls with identical force because each side of the 80 mm piston sees the rod-side area: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa in either direction. Twin guide rods on the yoke stop the tooling turning and take side load, so a press plate or gripper stays square without an external guide. The magnet fitted under the -S code lets CMSE / DMSE reed or solid-state switches report end positions directly on the body.
The hard-anodized aluminium body with an S45C hard-chrome plated 20 mm rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, from -20 to +70 C. As an ISO 21287 compact build it saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters inside guarded weld cells or gantry clamps. At 0.5 MPa plan on roughly 1414 N of real work, and the 2356.2 N rating lifts about 240 kg vertically - halve that for a 2:1 margin and it still raises about 120 kg. Fixed TPU bumpers absorb the end-of-stroke shock at both covers.
Airtac TACED Guided Compact Cylinder TACED80X60S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X60S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X60S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X60S Is Used
Weld fixture clamping
The equal 2356.2 N push and pull clamps and retracts steel brackets inside a tight weld cell, where the short ISO 21287 body fits the 60 mm gap a longer profile cylinder cannot.
Pallet stamping press
Twin guide rods keep the stamp head square over carton labels at 30-500 mm/s, with the TPU bumpers soaking up each end-of-stroke hit on a high-cycle line.
Battery tray lift-assist
The through-rod lifts about 120 kg of tray with a 2:1 margin, and CMSE switches on the -S magnet confirm top-of-stroke before the robot picks.
Is the Airtac TACED Guided Compact Cylinder TACED80X60S the Right Cylinder?
For this force class the 80 mm bore sits between the 63 mm (1458.1 N at 0.5 MPa) and the 100 mm (3769.9 N at 0.5 MPa) - drop to 63 for lighter clamps, go to 100 when the 2356.2 N here leaves too little margin. The 60 mm stroke is within the standard range for bore 80, so no made-to-order build is needed. Remember the piston drifts if air is lost; add a rod lock or pilot check valve where a load must stay put. Mount with the FB flange, and keep the -S magnet in the code since this model already carries it for CMSE / DMSE switching.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X60S FAQ
Yes - the double-rod design means a rod exits both covers, so both strokes act on the rod-side area of the 80 mm piston. Output is 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa in either direction, peaking at 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with proof at 1.5 MPa (215 psi).
This version carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches mount directly in the body slots for end-of-stroke signals. Mounting is via the FB flange, and the female M12x1.75 rod thread on the 20 mm rod accepts standard tooling. The 1/4" port serves the 80 mm bore, and the fixed TPU bumpers at both ends decelerate the piston without any adjustment.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X60S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.