Airtac TACED Guided Compact Cylinder TACED80X75S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X75S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X75S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED80X75S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an identical 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) in each direction - there is no smaller return stroke to design around. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a press plate or gripper stays square without an external guide. The -S code on this model means the magnet is fitted, and CMSE / DMSE reed or solid-state switches can be clamped straight onto the body slots.
The hard-anodized aluminium body with a roller-burnished bore and an S45C hard-chrome-plated rod shrugs off wear in high-cycle service, while fixed TPU bumpers at both ends absorb end-of-stroke shock. Because the short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, it drops into tight press frames and gantries. For planning: keep real work to roughly 1414 N (about 0.6 of the rating), which corresponds to lifting about 120 kg vertically with a 2:1 margin. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, ports 1/8".
Airtac TACED Guided Compact Cylinder TACED80X75S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X75S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X75S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X75S Is Used
Stamping die clamp in a press frame
The double rod clamps a sheet-metal die from both sides with an equal 2356.2 N at 0.5 MPa, and the twin guide yoke keeps the clamp shoe square under side load.
Push-pull transfer on an SMT pallet line
One cylinder advances and retracts a pallet stop with identical force in each direction, while the fitted -S magnet and a DMSE switch confirm end positions to the PLC.
Vertical part-lift on an assembly gantry
With about 120 kg of vertical lift capacity at a 2:1 margin, the 80 mm bore raises transmission brackets between stations inside a compact gantry head.
Is the Airtac TACED Guided Compact Cylinder TACED80X75S the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, this 80 mm bore suits clamping and pressing work in the 1400 N usable range; step down to the 63 mm bore (1458.1 N) for lighter dies or up to the 100 mm bore (3769.9 N) for heavy fixtures. The through-rod gives equal force both ways, so size the circuit once. Note it will not hold position if air is lost - add a rod lock or pilot check valve for a held load. FB flange mounting and the fitted -S magnet for CMSE / DMSE switches round out the spec; the 75 mm stroke sits well inside the 300 mm maximum standard stroke for this bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X75S FAQ
Yes - the double-rod design exits a 20 mm rod from both covers, so both sides work on the rod-side area. Output is 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, equal both ways, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 75 mm stroke is within the 300 mm maximum standard stroke for this bore.
This model carries the optional -S magnet, so CMSE or DMSE reed / solid-state switches mount directly in the body slots for end-position feedback. The ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and fixed TPU bumpers at both ends absorb end-of-stroke shock; the piston will drift if air is lost, so use a rod lock or pilot check valve where a load must stay held.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.