Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø100mm bore, 75mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ100 mm
- Stroke75 mm
- Port sizePT3/8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75
The AirTAC TACQ100X75 is a double-acting JIS compact guided cylinder featuring a 100mm bore and 75mm stroke. It integrates two chromed carbon steel guide rods with a fixing plate to drive and guide a load simultaneously, eliminating the need for a separate linear guide. The platform guarantees non-rotating accuracy of ±0.15° and handles lateral loads that a plain compact rod cannot withstand.
Drive force equals a standard ACQ of the same bore, as the guides add stiffness rather than thrust. At 0.5 MPa, it provides 3927N push and 3524.8N pull force, requiring a PT3/8 port. The unit uses fixed NBR elastomer bumpers for end-of-stroke deceleration rather than adjustable air cushions. Since this specific configuration lacks a magnet, the body grooves remain ready for reed or solid-state switches if a separate sensor version is later required.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø100 mm |
| Stroke | 75 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT3/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 Is Used
Heavy Press Assembly
Applies 5497.8N of thrust at 0.7 MPa for seating large automotive bearings while maintaining strict ±0.15° parallelism.
Pallet Stopper Gate
Functions as a high-load stopper arm on conveyor lines, absorbing heavy side impacts without rotational deflection.
Panel Bending Fixture
Forms sheet metal workpieces where twin guide rods prevent twisting under offset loads during the bending cycle.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 the Right Cylinder?
For 0.5 MPa push requirements around 2513N, the smaller TACQ80X75 offers a capable alternative, whereas the TACQ100X75 is the maximum standard bore available in this series. If your application only needs basic thrust without lateral load resistance or anti-rotation, a plain ACQ cylinder suffices. Confirm your ordering essentials: 100mm bore, 75mm stroke (under the 100mm maximum), and PT thread. You must verify the allowable reverse torque limit and mass/speed constraints charted at 0.5 MPa from the datasheet, ensuring any external force is applied concentric with the rod.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75 FAQ
The TACQ100X75 delivers 3927N push and 3524.8N pull at 0.5 MPa, 5497.8N push at 0.7 MPa, and a maximum push of 801kgf at 1.0 MPa. It has a 75mm stroke (maximum standard is 100mm) and a non-rotating tolerance of ±0.15°.
Two chromed carbon steel guide rods manage lateral loads and prevent rotation. The maximum allowable reverse torque decreases with stroke extension; treat the datasheet chart as an order-of-magnitude guide and confirm the exact limit. Never exceed this torque, and apply external force concentrically with the rod.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ100X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.