Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø32mm bore, 15mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ32 mm
- Stroke15 mm
- Port sizePT1/8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S
The AirTAC TACQ32X15S is a double-acting JIS compact guided cylinder integrating two stainless steel guide rods and a fixing plate with a standard ACQ body. This build drives and guides your load simultaneously, eliminating the need for a separate linear rail. The twin rods ensure non-rotating accuracy of ±0.15° for this 32mm bore, actively resisting lateral loads and side forces that a plain rod cannot withstand.
Drive force equals a standard ACQ of the same bore, as the guides add stiffness rather than thrust. At 0.5 MPa it delivers 402.1N push and 301.6N pull, with a maximum push of 82kgf at 1.0 MPa. It features a fixed NBR elastomer bumper at each end for end-of-stroke deceleration, plus a built-in magnet (-S) for position sensing. The standard PT1/8 port and M8x1.25 rod-end thread simplify integration into existing machinery.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø32 mm |
| Stroke | 15 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT1/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 32 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S Is Used
PCB Pick-and-Place Head
Drives a small vacuum gripper for electronic board assembly, using the twin guide rods to maintain exact vertical alignment without twisting during the pick cycle.
Component Testing Press
Applies a precise 402.1N clamping force at 0.5 MPa onto connectors or micro-switches, relying on the ±0.15° non-rotating tolerance to prevent uneven pin loading.
Sensor Positioning Slide
Advances a vision camera or laser probe 15mm into inspection range, with the fixed elastomer bumpers ensuring soft, repeatable landing at the test position.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S the Right Cylinder?
Choosing this 32mm bore with a 15mm stroke offers high force in a very short footprint. If you need less thrust, the 25mm bore provides 245.4N push at 0.5 MPa, while stepping up to the 40mm bore yields 628.3N push. A plain ACQ fits better if your load is already externally guided and you do not need anti-rotation. For pulling or pressing equally from both sides, a double-rod ACQD is superior. When ordering, confirm the 15mm stroke is within the 100mm maximum, specify the -S magnet, and verify your lateral load and reverse torque fall within the allowable limits.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S FAQ
This 32mm bore double-acting cylinder provides 402.1N push and 301.6N pull at 0.5 MPa, 562.9N push at 0.7 MPa, and a maximum 82kgf push at 1.0 MPa. It has a PT1/8 port, an M8x1.25 rod-end thread, and a non-rotating tolerance of ±0.15°. The maximum standard stroke for this bore is 100mm.
No, a standard ACQ-type body does not hold its load on air loss; the rod drifts and the fixed NBR bumper only decelerates near stroke end. For fail-safe holding, use an external rod lock or pilot-operated check valve. The twin guide rods carry lateral loads, but maximum allowable reverse torque decreases with stroke—confirm the exact limit for your setup from the datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.