Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø32mm bore, 75mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ32 mm
- Stroke75 mm
- Port sizePT1/8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S
The AirTAC TACQ32X75S is a double-acting JIS compact guided cylinder featuring a 32mm bore and 75mm stroke. It integrates twin stainless steel guide rods with a fixing plate to deliver non-rotating accuracy of ±0.15°. This design carries lateral loads and replaces a separate linear guide, driving and guiding your payload in one unit.
Drive force equals a standard ACQ of the same bore, as the guides add stiffness rather than thrust. It supplies 402.1N push and 301.6N pull at 0.5MPa, or 562.9N push at 0.7MPa. The -S suffix denotes a built-in piston magnet compatible with reed or electronic solid-state switches. End-of-travel deceleration is handled by fixed NBR elastomer bumpers, not adjustable air cushions.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT1/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S Is Used
Pick-and-Place Head
Ideal for mounting small grippers on electronics assembly lines where maintaining exact angular alignment during vertical placement is critical.
PCB Inspection Slide
Provides stable vertical movement for camera sensors in semiconductor fabrication, preventing platform wobble during image capture.
Pallet Stopper Gate
Functions as a rigid stop mechanism on packaging conveyors, absorbing side impacts without deflecting or twisting.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S the Right Cylinder?
When sizing this 32mm bore, dropping down to a 25mm bore yields 245.4N push at 0.5MPa, while stepping up to a 40mm bore provides 628.3N push at 0.5MPa. Choose this guided unit if your payload requires anti-rotation support or lateral load capacity. If your application only needs basic linear thrust without lateral resistance, a plain ACQ cylinder is more economical. For higher drive force without adding guide rods, a double-rod ACQD is an alternative. Confirm your ordering essentials: 32mm bore, 75mm stroke (max standard 100mm), -S magnet, and PT1/8 port. Always verify the mass, speed limits, and reverse torque limits from the datasheet before finalizing.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S FAQ
This 32mm bore double-acting cylinder delivers 402.1N push and 301.6N pull at 0.5MPa, 562.9N push at 0.7MPa, and a maximum push of 82kgf at 1.0MPa. It features a PT1/8 port, an M8x1.25 rod-end thread, and a non-rotating tolerance of ±0.15°. The maximum standard stroke for this bore is 100mm.
The -S suffix indicates a built-in piston magnet for position sensing with reed or electronic solid-state switches. The twin guide rods allow it to carry lateral loads a plain compact rod cannot. There is a maximum allowable reverse torque and mass/speed limit charted at 0.5MPa that decreases with stroke length; you must confirm the exact value for this 75mm stroke from the datasheet and never apply external force exceeding these limits or off-axis from the rod.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ32X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.