Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø40mm bore, 5mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ40 mm
- Stroke5 mm
- Port sizePT1/8
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5
The AirTAC TACQ40X5 is a double-acting JIS compact guided cylinder featuring a 40mm bore and 5mm stroke. It integrates two stainless steel guide rods with a fixing plate, driving and guiding a load simultaneously to replace a separate linear guide. The twin rods ensure non-rotating accuracy of ±0.15°, supporting lateral loads that a plain compact rod cannot manage.
Drive force equals a standard ACQ of the same bore, as the guides add stiffness rather than thrust. At 0.5 MPa it provides 628.3N push and 527.8N pull, scaling to 879.6N push at 0.7 MPa, with a maximum push of 128 kgf at 1.0 MPa. It uses a PT1/8 port, an M8x1.25 rod-end thread, and fixed elastomer NBR bumpers at each end for end-of-stroke deceleration. Note that this specific model ships without a sensor magnet.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø40 mm |
| Stroke | 5 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT1/8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 40 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 Is Used
Pick-and-Place Head
Ideal for mounting small grippers on electronic assembly lines where precise vertical placement and ±0.15° non-rotation are critical.
Sensor Slide
Moves inspection cameras or laser profilers across a stationary web, using the dual guide rods to maintain strict angular stability.
Component Stopper Gate
Acts as a short-stroke physical stopper on a conveyor, absorbing side-impact loads without deflecting or twisting.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 the Right Cylinder?
Choosing this 40mm bore with a 5mm stroke is optimal for extremely short, high-rigidity positioning. If lower force is acceptable, a 32mm bore provides 402.1N push at 0.5 MPa; stepping up to a 50mm bore yields 981.8N push. A plain ACQ fits if no lateral load or anti-rotation guidance is required, while a double-rod ACQD offers higher bending resistance. Confirm ordering essentials: bore, stroke (under the 100mm max), thread type (PT default), and magnet option (this unit lacks the -S suffix). Always verify the allowable reverse torque and mass/speed limits from the datasheet, and ensure external forces are applied concentric with the rod.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5 FAQ
The TACQ40X5 has a 40mm bore and 5mm stroke (max standard stroke is 100mm). It delivers 628.3N push and 527.8N pull at 0.5 MPa, 879.6N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. The two guide rods provide a non-rotating tolerance of ±0.15°.
No, a plain ACQ-type body does not hold its load on air loss; the rod drifts and the fixed bumper only decelerates near stroke end. For a fail-safe hold, use an external rod lock or pilot-operated check valve. Also, do not exceed the maximum allowable reverse torque, which decreases with stroke length—confirm the exact limit for your setup from the datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ40X5
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.