Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75
The AirTAC Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 is a genuine double-acting GUIDED compact (JIS) cylinder — a Ø50mm bore, 75mm stroke and two guide rods with a fixing plate. The twin guides hold the platform non-rotating to within ±0.15° and carry lateral load a plain compact rod cannot, so it drives and guides a load in one unit.
- BoreØ50 mm
- Stroke75 mm
- Port sizePT1/4
- Acting typeDouble acting, guided
- Non-rotating±0.15°
- CushionBumper (both ends)
About the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75
The AirTAC TACQ50X75 is a double-acting JIS compact guided cylinder featuring a 50mm bore and 75mm stroke. It integrates two chromed carbon steel guide rods with a fixing plate to drive and guide a load simultaneously, effectively replacing a separate linear guide. The twin-rod mechanism ensures non-rotating accuracy of ±0.15° and provides superior lateral load capacity compared to a plain compact rod.
Drive force matches a standard ACQ of the same bore, as the guides add stiffness rather than thrust. At 0.5 MPa it yields 981.8 N push and 824.6 N pull, reaching 1374.4 N push at 0.7 MPa with a maximum push of 200 kgf at 1.0 MPa. The unit uses a PT1/4 port, an M10x1.5 female rod-end thread, and a fixed NBR elastomer bumper at each end. Note this specific configuration ships without a sensor magnet, though the body retains switch grooves.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 Technical Specifications
| Model | Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 |
|---|---|
| Series | TACQ JIS guided compact cylinder |
| Bore size | Ø50 mm |
| Stroke | 75 mm |
| Acting type | Double acting, guided (non-rotating) |
| Non-rotating tolerance | ±0.15° |
| Port size | PT1/4 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC TACQ datasheet. Two guide rods carry lateral load and hold rotation to ±0.15°; do not apply reverse torque beyond the datasheet limit. Confirm against the product label before installation.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Drive force equals a standard ACQ of the same bore — the guide rods add stiffness, not thrust. Keep moving mass and speed within the datasheet chart (rated at 0.5 MPa).
Model Code: Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75
| TACQ | JIS compact cylinder WITH guider (non-rotating). |
|---|---|
| 50 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch sensing (omit = none). |
| thread | Blank = PT; G or NPT available. |
The guide plate replaces a separate rod-thread option. Related: ACQ (plain single rod), ACQD (double rod), ACQJ (adjustable stroke).
Where the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 Is Used
Pick-and-Place Head
Drives a vertical suction cup array on an electronics assembly line, relying on the ±0.15° non-rotating tolerance to keep components flat during transfer.
Vision Camera Slide
Positions an inspection camera over a moving conveyor with high lateral stiffness, preventing deflection from cable drag or external vibration.
Carton Stopper Gate
Acts as a pneumatic stop gate on a packaging conveyor, absorbing side impacts from cartons while maintaining a rigid vertical blocking position.
Is the Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 the Right Cylinder?
When sizing this 50mm bore, consider the neighboring options: a 40mm bore provides 628.3 N push at 0.5 MPa, while a 63mm bore offers 1558.6 N. Choose the TACQ50X75 when your application requires the 981.8 N thrust alongside precise anti-rotation stability. If lateral load support is unnecessary, a plain ACQ cylinder saves space and weight; for higher opposing thrust needs, a double-rod ACQD might fit better. Verify your stroke is within the 100mm maximum, confirm the PT1/4 thread requirement, and always check the reverse torque and mass limits charted at 0.5 MPa to ensure they match your dynamic load.
Quick checklist
- ✓ Lateral load / non-rotation needed?
- ✓ Moving mass and speed within chart
- ✓ Drive force at your pressure
- ✓ Magnet (S) for sensors?
- ✓ No reverse torque on the guide rods
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Do not apply reverse torque above the datasheet limit.
- check Apply external force concentric with the rod.
- check Keep mass × speed within the performance chart.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75 FAQ
The TACQ50X75 has a 50mm bore and a 75mm stroke (maximum standard stroke is 100mm). It generates 981.8 N push and 824.6 N pull at 0.5 MPa, 1374.4 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. The dual guide rods provide a non-rotating tolerance of ±0.15°.
The two chromed carbon steel guide rods allow it to carry lateral loads a plain rod cannot. However, there is a maximum allowable reverse torque and mass/speed limit that decreases with stroke length. Use the order-of-magnitude values charted at 0.5 MPa as a guide and confirm the exact limit for your setup from the datasheet. Always apply external force concentric with the rod to avoid exceeding the torque limit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TACQ Guided Cylinders
Request a Quote for Airtac TACQ Guided Rod Ultra-Thin Cylinder TACQ50X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.