The AirTAC Airtac TR Twin-Rod Cylinders TR32X100ST is a genuine TR twin-rod (double-rod) double-acting cylinder, 32 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 804.3 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
The TR32X100ST is a double-acting twin-rod cylinder: two parallel rods carried on one shared plate keep the load from rotating and give the plate strong resistance to bending and twisting, so the workpiece can mount directly on the plate. With a 32 mm bore and 100 mm stroke, it delivers a theoretical push thrust of about 804.2 N at 0.5 MPa, and its adjustable bumper cushions end-of-stroke impact while allowing stroke adjustment over -5 to 0 mm. This is a genuine AirTAC part built to the JIS standard, the precise guide-grade twin-rod series with high non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubricant. A position-detecting magnet is fitted as standard, with magnetic-switch slots machined around the body. Overall dimensions for the 100 mm stroke and any sizing checks are confirmed from the datasheet on request.
| Model | Airtac TR Twin-Rod Cylinders TR32X100ST |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 32 mm |
| Push thrust @0.5 MPa | 804.3 N |
| Port size | 1/8" (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
Choose the bore for thrust first: at 0.5 MPa push this 32 mm bore gives a theoretical 804.2 N (pull side is lower), and it operates over 0.15-1.0 MPa (22-145 psi). The TR is AirTAC's JIS-standard twin-rod series with the precise guide grade; if you need the enterprise-standard series instead, the TN covers the same bore sizes but is PT-thread only, while the TR offers PT, G, or NPT - this model takes NPT. Stroke 100 mm sits within the 32 mm bore's stroke table; avoid stretching to over-long strokes beyond the table, and use the short-cover option if a shorter built-in length matters. Confirm side-load capability and exact dimensions from the datasheet, or ask us and we will route them to you.
Mounted across a conveyor line, the plate rises or extends square to the product flow to stop pallets or totes at a gate. The twin rods keep the stop face from rotating or skewing under repeated hits, and the adjustable bumper soaks up the impact at each stop.
On packaging and assembly lines, the cylinder pushes cartons or trays sideways between lanes. The shared plate gives a wide, non-rotating push face, so the load stays square through the 100 mm stroke instead of twisting off line.
Fitted under a fixture or nesting plate, the twin-rod cylinder lifts parts squarely to a pick or inspect position. The two rods resist the twisting that a single-rod actuator would see from off-center loads, keeping the presented part level.
Both cover the 32 mm bore and both are double-acting twin-rod cylinders, but they are different standards. The TR32X100ST is the JIS-standard, precise guide-grade TR: higher non-rotating accuracy, low rod-end deflection, a lengthening sliding-support guide that needs no added lubricant, and two groups of ports, one on each side. The TN is the enterprise-standard series and is PT-thread only, while the TR offers PT, G, or NPT. Pick TR when guide precision or port access on both sides matters; pick TN for the enterprise standard with PT ports.
The TR32X100ST uses an external front bumper, not an air cushion: it cushions the impact at end of stroke and doubles as a stroke adjuster over a -5 to 0 mm range. Because the two rods ride on one shared plate, the load mounted on the plate is held against rotation and the plate resists bending and twisting. The exact allowable side load for your application is published as curves, so confirm it from the datasheet or ask us before sizing.