The AirTAC GFR20006MLJC2WG AirTAC Filter Regulator G1/8, 5 um is a genuine G-series filter regulator: water separation, 5 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has PT1/8" ports, a manual drain and regulates 0.05 - 0.9 MPa (7 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
The AirTAC GFR20006MLJC2WG is a GFR-series filter regulator: filtration and pressure regulation combined in a single body, with a drain bowl but no lubricator. This 200-size unit is built with a G1/8 (BSPP) port, a 5 um filter element for finer particulate and water removal than the standard 40 um grade, and a manual drain you operate by hand as part of routine checks. It is the low-pressure regulator type, fitted with an external round gauge scaled in psi, and supplied without a mounting bracket. Maximum inlet pressure is 1.0 MPa (145 psi) and the working temperature range is -5 to 70 C (non-freezing).
This is a genuine AirTAC part from the GFR200 series, one of four sizes (200/300/400/600) in the GFR line, with port sizes, thread options (PT standard, G and NPT to order), drain types, filter grades and gauge choices across the range. Flow is published as curves rather than a single rated figure, so ask us to confirm the datasheet and sizing for your application before ordering.
| Model | GFR20006MLJC2WG AirTAC Filter Regulator G1/8, 5 um |
|---|---|
| Series | GFR200 filter regulator |
| Port size | PT1/8" (G (BSPP) thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.05 - 0.9 MPa (7 - 130 psi) |
| Pressure type | Low-pressure type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Manual drain |
| Bowl material | PC |
| Pressure gauge | Fitted — round, psi scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| M | Drain: Manual drain — this also sets the regulating band (0.05 - 0.9 MPa (7 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| J | Supplied without bracket. |
| (blank) | Pressure gauge fitted (blank). |
| C | Gauge shape: Round. C is round, F is square. |
| 2 | Gauge scale: psi. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| G | G (BSPP) thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · PT1/8" · 5 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-06 (two-unit set) |
Feeds filtered, regulated air to low-pressure actuation circuits on packaging machinery, where the 5 um element protects downstream valves and the round psi gauge gives operators a clear setpoint reading.
Suits a laboratory test bench or pilot rig needing fine 5 um filtration and gentle, stable regulation at low pressure, with the manual drain letting technicians blow down the bowl between runs.
Conditions the air line ahead of spray guns or coating heads, removing water and fine particulate at 5 um and holding a low, steady working pressure so finish quality stays consistent.
The GFR200 is the smallest size step in the GFR range; if your line needs more flow, the 300/400/600 sizes step up in port and capacity, so match the size to the air demand of the circuit rather than the port alone. This code fixes the real choices: 5 um filtration (choose 40 um if coarse protection is enough), a manual drain (choose automatic or differential-pressure drain where manual blowdowns are impractical), the low-pressure regulator type, a round psi gauge (square embedded gauges and MPa/bar scales are alternatives), G thread (PT standard, NPT to order) and no bracket. Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before ordering.
Quick checklist
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC publishes flow for the GFR series as curves, not as a single rated figure, so we do not quote a number here. Tell us your application and required air demand and we will confirm the flow and sizing from the datasheet on request before you order.
The M in the code specifies a manual drain: accumulated water is released by hand, which suits installations checked as part of a routine. The L in the code makes this the low-pressure regulator type rather than the standard type; its exact regulation range is not published in the material we hold, so ask us to confirm it from the datasheet for your setpoint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.