The AirTAC TR10X10S AirTAC Twin-Rod Cylinder 10mm Bore, 10mm Stroke is a genuine TR twin-rod (double-rod) double-acting cylinder, 10 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 78.6 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
The TR is AirTAC's JIS-standard twin-rod cylinder: two parallel rods drive one shared plate, so the plate resists bending and twisting and the load mounts on it without rotating. This 10 mm bore model with a 10 mm stroke gives a theoretical push thrust of 78.5 N at 0.5 MPa (the pull side is lower), and the external bumper at the front of the body both cushions impact and adjusts the effective stroke over -5 to 0 mm. It runs on air filtered to 40 um at 30-500 mm/s.
This is a genuine AirTAC part built to the JIS standard, with the TR series' precise guide for higher non-rotating accuracy and low rod-end deflection. A position-detecting magnet is fitted as standard, with magnetic-switch slots around the body, and the body carries two groups of ports, one on each side. We confirm dimensions for this stroke and any sizing checks from the datasheet on request.
| Model | TR10X10S AirTAC Twin-Rod Cylinder 10mm Bore, 10mm Stroke |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 10 mm |
| Push thrust @0.5 MPa | 78.6 N |
| Port size | M5x0.8 (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.2 - 1.0 MPa (29 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
Bore sets the thrust: this 10 mm bore delivers 78.5 N theoretical push at 0.5 MPa with an operating pressure of 0.2-1.0 MPa (29-145 psi), so step up a bore size in the same series if you need more force. The stroke here is 10 mm; other lengths are available within the 10 mm bore's stroke table, but avoid over-long strokes that run past the short-cover design range. The thread on this code is PT; the TR series can also be ordered with G or NPT. Compared with the enterprise-standard TN (10-32 mm bores, PT only), the JIS TR adds a lengthening sliding-support guide that needs no added lubrication, two-side ports, and higher non-rotating precision. Allowable side load is published only as curves - route your load case to us and we will confirm it from the datasheet.
Bolted to the line frame, the plate pushes cartons squarely off a lane at a transfer point; the twin rods keep the push face from rotating through the full 10 mm stroke.
Clamps a workpiece in a drilling or welding jig; the two parallel rods absorb the twisting reaction of the clamp lever so the pad stays square to the part.
Presents a stop blade across a roller conveyor to pause arriving parts; the external bumper cushions each impact and lets you trim the stop position by up to 5 mm.
The code decodes as TR (JIS-standard twin-rod), 10 mm bore, 10 mm stroke, S for the standard magnet, and no thread letter, which means PT ports. If your manifold uses BSP or NPT fittings, order the G or NPT thread versions of the same bore and stroke instead - the TR series offers PT, G and NPT, and it provides two groups of ports, one on each side of the body.
Yes - the twin-rod design resists rotation, bending and twisting through its two parallel rods, and the TR's precise guide keeps rod-end deflection low, so the load mounts directly on the plate. Allowable side load is published only as curves, so confirm your off-center load against the datasheet or ask us before final mounting.