The AirTAC TR16X80S AirTAC 16 mm Twin-Rod Cylinder, 80 mm Stroke is a genuine TR twin-rod (double-rod) double-acting cylinder, 16 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 201.1 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range. As the JIS guide-grade series it adds high non-rotating precision, a lengthening sliding guide (no added lubricant) and two-side ports.
The TR16X80S is a double-acting twin-rod cylinder: two parallel rods carry one shared plate, so the load mounts without rotating and the plate resists bending and twisting. The 16 mm bore gives a theoretical push thrust of about 100.5 N at 0.5 MPa (the pull side is lower), while the 80 mm stroke provides the longer travel needed for diverting, lifting and press-approach motions in light-duty tooling. A front bumper cushions impact and adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the JIS standard, in the TR guide-grade design with higher non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubrication. The magnet is standard on every TR cylinder, with magnetic-switch slots around the body, and this model is supplied with PT ports. We confirm dimensions and sizing from the datasheet on request.
| Model | TR16X80S AirTAC 16 mm Twin-Rod Cylinder, 80 mm Stroke |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TR (JIS standard) |
| Bore | 16 mm |
| Push thrust @0.5 MPa | 201.1 N |
| Port size | M5x0.8 (PT, G or NPT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
The 16 mm bore suits work needing around 100.5 N of theoretical push thrust at 0.5 MPa; move up to the 20/25/32 mm bores for more thrust or down to 6/10 mm for less. TR is the JIS-standard twin-rod series with the precise guide, and unlike the enterprise-standard TN series it offers PT, G and NPT thread options - this model carries PT. This 80 mm stroke sits at the longer end of the 16 mm bore's table, so take care against over-long strokes for this bore and confirm the fit from the datasheet. For side-load capability, ask us and we will check the published curves with you.
Swings or lifts a divert gate on a sorting conveyor over an 80 mm throw, the twin rods keeping the gate plate from twisting as it moves.
Raises and lowers a gravity-chute gate or hopper shutter between two positions, holding the gate plate level without rotating.
Brings a crimping or staking head down onto terminals over the 80 mm approach, with the twin rods keeping the head plate square to the part.
TR is the AirTAC JIS-standard twin-rod series and is available with PT, G or NPT ports - this TR16X80S model is supplied with PT. The TN series is the enterprise-standard twin-rod series instead and is offered in PT only. TR also carries the precise guide-grade features such as higher non-rotating accuracy and two groups of ports, one on each side.
Side-load capability and rod-end deflection are published as curves rather than single numbers, and overall dimensions vary with stroke, so both are confirmed from the datasheet - send us your application and we will check the figures with you.