Airtac 3V1 Solenoid Valve 3V106C7F-AM
The AirTAC Airtac 3V1 Solenoid Valve 3V106C7F-AM is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
- Valve type3/2-way (3-port, 2-position)
- Port size1/8 in
- Coil voltageAC110V
- Electrical entryDIN plug (DIN socket type)
- Stations7
- Series3V1
About the Airtac 3V1 Solenoid Valve 3V106C7F-AM
Seven 3/2 stations on one base: 3V106C7F-AM turns seven feed-or-vent circuits into a single compact bank. Direct acting with spring return, each valve either pressurises its outlet or exhausts it, which suits single-acting cylinders, clamps, blow duty and pilot signals alike.
Each AC110V coil draws 4.5 VA on a DIN plug connection, the housing is IP65 (DIN 40050) rated, and the medium must be air filtered to 40 um or finer. Manual overrides on every station simplify setup and fault-finding on the machine.
Airtac 3V1 Solenoid Valve 3V106C7F-AM Technical Specifications
| Model | Airtac 3V1 Solenoid Valve 3V106C7F-AM |
|---|---|
| Series | 3V1 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Port size | 1/8 in |
| Thread | PT |
| Coil voltage | AC110V |
|---|---|
| Electrical entry | DIN plug (DIN socket type) |
| Coil power | 4.5 VA |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Not rated for vacuum |
| Flow coefficient | Not published for 3V1 |
| Temperature | -20 to 70 C |
| Construction | Direct-acting, single solenoid, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V1 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
Model Code: Airtac 3V1 Solenoid Valve 3V106C7F-AM
| 3V1 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/8 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| AC110V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| — | Electrical entry: I = flying lead, otherwise a DIN plug. |
| 7F | 7 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V1 Solenoid Valve 3V106C7F-AM Is Used
Process-valve pilot bank
Seven pilot signals for larger process valves leave one shared supply, cutting tubing runs across a water-treatment skid.
Pick-and-place grippers
Spring-return gripper cylinders in a fast electronics assembly cell cycle on 4.5 VA coils, keeping the control cabinet load light.
Guard-lock venting
Feed the gate-lock cylinder while the cell runs and vent it when the guard opens - a duty where spring return behaviour counts.
Is the Airtac 3V1 Solenoid Valve 3V106C7F-AM the Right Part?
With no published Cv for the 3V1 body, 3V106C7F-AM should be chosen for its compactness and low coil draw rather than for flow - confirm any flow-critical duty with us. If the circuit needs more air, step up to 3V2 (1/8in and 1/4in, NC or NO selectable, Cv 0.18-0.19, vacuum rated) or 3V3 (1/4in, Cv 0.62); 3V2M suits dense manifolds where flow is secondary.
Lock down five choices at ordering: M5 or 1/8in port; thread (PT is the family default, G and NPT are order options); coil voltage; DIN plug or flying lead; and the manifold station count. For double-acting cylinder duty, switch to the 5-port AirTAC 4V series.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
- check Match the coil voltage to your controller output.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V1 Solenoid Valve 3V106C7F-AM FAQ
Pressure 0-0.8 MPa (0-114 psi); temperature -20 to 70 C; air filtered to 40 um or better; IP65 (DIN 40050). Coil draw: 4.5 VA at AC110V (AC220V also 4.5 VA, AC24V 5.0 VA, DC24V 3.0 W, DC12V 2.5 W). AirTAC states no Cv for the 3V1 body, so verify any flow-critical duty with us.
Yes - the catalogue lists AC220V, AC110V, AC24V, DC24V and DC12V coils, DIN plug or flying-lead entry, and G or NPT threads as order options (PT is the standard thread on this family), with station counts from 1F to 20F. Specify your requirements in an RFQ and we confirm the exact code for you.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac 3V1 Solenoid Valve 3V106C7F-AM
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.