Airtac ACED Double-acting Compact Cylinder ACED100X175S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X175S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 175mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke175 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X175S
The ACED100X175S is a double acting, double-rod compact cylinder built to ISO 21287: a piston rod leaves both covers, so push and pull force are identical because both strokes work on the rod-side area. At 0.5 MPa this 100 mm bore delivers 3769.9 N in either direction, rising to 5277.9 N at 0.7 MPa. The through-rod resists rotation and side load, and the rear rod gives you a free mounting point or a sensor flag. Its hard-anodized aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, so it slots into gantries and press fixtures where a full-length body cannot.
The S in the code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped onto the body slots for end-of-stroke signalling. A fixed TPU bumper at each end absorbs stroke-end shock, the S45C hard-chrome plated rod handles wear, and speed runs 30-500 mm/s. As a rule of thumb, plan on roughly 2262 N of usable work at 0.5 MPa, which is about 115 kg of vertical lift with a 2:1 margin - enough to raise a loaded pallet clamp or a heavy weldment fixture. Air supply is filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C.
Airtac ACED Double-acting Compact Cylinder ACED100X175S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X175S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X175S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X175S Is Used
Pallet clamp lifting
The symmetric through-rod lifts a pallet-clamp platen squarely from both sides; with about 115 kg of vertical lift capacity at a 2:1 margin, the 100 mm bore handles loaded pallets on packaging lines.
Weld fixture clamping
In automotive weld cells the equal 3769.9 N force both ways clamps heavy stampings identically on approach and return, while the short ISO 21287 body fits between fixture rails.
Gantry position feedback
The fitted -S magnet lets CMSE / DMSE switches ride the body slots, so a gantry press reports mid-stroke and end positions over the 175 mm travel without external flags.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X175S the Right Cylinder?
Step down to an ACED80 (2356.2 N at 0.5 MPa) when the load is under about 230 kgf, or step up to an ACED125 (5890.5 N) for presses and heavy clamping. The 175 mm stroke sits well inside the 300 mm maximum standard stroke for this bore, so it ships as a catalogue item. Note that like any plain double-rod cylinder it will drift if air is lost - add a rod lock or pilot check valve where a load must be held. Mount with FA/FB flanges, LB foot or FTC brackets plus I/Y rod knuckles, and the fitted -S magnet pairs with CMSE / DMSE switches. Female M12x1.75 rod thread, PT ports, 1/4".
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X175S FAQ
Yes - the double-rod design means a rod exits both covers, so both strokes use the rod-side area. Output is 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa, identical in push and pull, with a maximum of 768.8 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s.
The S means the optional -S magnet is fitted on this model, so CMSE / DMSE reed or solid-state switches can be mounted in the body slots for position sensing. The ISO 21287 compact body is hard-anodized aluminium with an S45C hard-chrome rod, about 50% shorter in mounting length than an ISO 15552 profile cylinder, with a fixed TPU bumper at each stroke end and FA/FB, LB or FTC mounting options.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X175S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.