Airtac ACED Double-acting Compact Cylinder ACED100X80B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X80B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 80mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke80 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X80B
A double acting compact cylinder built to ISO 21287, the ACED100X80B pushes a 100 mm bore through an 80 mm stroke with a rod leaving BOTH covers, so thrust is identical on the extend and retract strokes. At 0.5 MPa each direction delivers 3769.9 N, rising to 5277.9 N at 0.7 MPa. The through-rod resists rotation and side load and gives a symmetric mount, while the rear rod stub can carry a sensor flag on a fixture.
The hard-anodized aluminium body with an S45C hard-chrome plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, -20 to 70 C, with a fixed TPU bumper at each end. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into press fixtures and gantries where a full-length body will not fit. As a planning figure, about 2262 N of the 0.5 MPa rating is usable for real work, which lifts roughly 115 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED100X80B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X80B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X80B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X80B Is Used
Pneumatic press fixture
The 3769.9 N symmetric thrust at 0.5 MPa suits a riveting or staking head on an 80 mm stroke, with the through-rod keeping the tooling square under side load.
Pallet clamp on a transfer cart
Equal force both ways lets one valve circuit clamp and release a pallet load of about 115 kg with margin, and the short body fits the cart deck height.
Bidirectional pusher on a packaging line
Identical extend and retract force at 30-500 mm/s pushes cartons off a conveyor in either direction, with the TPU bumper quieting each end of the 80 mm travel.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X80B the Right Cylinder?
At this force class the neighbours matter: a 80 mm bore double-rod unit gives 2356.2 N at 0.5 MPa, while stepping up to 125 mm reaches 5890.5 N, so pick the 100 mm when your load sits between roughly 1400 and 2900 N of working demand. Remember that a plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check valve if the 80 mm stroke must hold position. Mounting brackets (FA/FB flange, LB foot, FTC) and I/Y rod knuckles bolt straight to the ISO 21287 face; the B code here gives a male 20 mm rod thread with a PT port, and the optional -S magnet enables CMSE / DMSE switches if you order it.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X80B FAQ
Yes - because a rod exits both covers, both strokes use the rod-side area. At 0.5 MPa you get 3769.9 N per direction, at 0.7 MPa you get 5277.9 N per direction, and the maximum rating is 768.8 kgf at 1.0 MPa. For sizing, treat about 2262 N (roughly 115 kg vertical lift with a 2:1 margin) as the usable working force at 0.5 MPa.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight guards and fixtures. Switches are possible only with the optional -S magnet code: order ACED100X80BS and CMSE / DMSE reed or solid-state switches clamp into the body slots. Without -S there is no magnet. This unit has a male rod thread (B code), PT ports at 1/4", and FA/FB, LB or FTC mounting options.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X80B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.