Airtac ACED Double-acting Compact Cylinder ACED125X35SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED125X35SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø125mm bore and 35mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ125 mm
- Stroke35 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM16×2.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED125X35SB
A double acting compact cylinder built to ISO 21287, the ACED125X35SB pushes a 125 mm bore through a 35 mm stroke with a rod leaving both covers. Because each side sees the rod-side area, output is a symmetric 5890.5 N at 0.5 MPa and 8246.7 N at 0.7 MPa in either direction. The male rod thread (B code) and the fitted -S magnet, ready for CMSE / DMSE switches, come as ordered on this variant.
The hard-anodized aluminium body with an S45C hard-chrome plated 25 mm rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, with a fixed TPU bumper at each end. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into heavy presses and gantries where a full-length body cannot. As a rule of thumb, plan on roughly 3534 N of real work at 0.5 MPa, and the rod-side force equates to lifting about 300 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED125X35SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED125X35SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø125mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED125X35SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 125 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED125X35SB Is Used
Heavy stamping press ejector
The 5890.5 N symmetric thrust at 0.5 MPa ejects formed steel panels from a die on both strokes, and the 35 mm stroke keeps the die block short.
Pallet clamp actuation
Equal force in both directions clamps and releases palletized loads in a warehouse line, with the through-rod resisting the side load of off-center clamps.
Bottle line pusher gate
A back-end rod carries a sensor flag while the front rod swings a reject gate on a bottling conveyor; the fitted magnet drives CMSE switch position feedback.
Is the Airtac ACED Double-acting Compact Cylinder ACED125X35SB the Right Cylinder?
At this force class the step down is the 100 mm bore (3769.9 N at 0.5 MPa) and the step up within the range ends at 125 mm itself, the largest bore offered. If the job needs a non-rotating rod, look at the TACED; for adjustable stroke, the ACEJ. Note that a plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check for held loads. FA/FB flange, LB foot and FTC brackets bolt to the ISO 21287 face, and this unit already carries the optional -S magnet for CMSE / DMSE sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED125X35SB FAQ
Yes. With a rod exiting both covers, both strokes use the rod-side area: 5890.5 N at 0.5 MPa and 8246.7 N at 0.7 MPa, equal push and pull. At 1.0 MPa the peak is 1201.3 kgf. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, bore 125 mm, stroke 35 mm, port 1/4" PT.
The -S magnet is fitted on this model, so CMSE reed or DMSE solid-state switches mount directly in the body slots. FA/FB flanges, LB foot and FTC brackets attach to the ISO 21287 face, and the fixed TPU bumper at each end absorbs end-of-stroke energy. For exact outline dimensions, confirm from datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED125X35SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.