Airtac ACED Double-acting Compact Cylinder ACED40X200
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED40X200 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø40mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ40 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED40X200
A double acting compact cylinder built to ISO 21287, the ACED40X200 pushes a 40 mm piston over a 200 mm stroke with a rod leaving BOTH covers. Because each stroke works on the rod-side area, output is identical in either direction: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa. The through-rod resists rotation and modest side load, and the rear rod can carry a sensor flag or a second tooling plate.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, from -20 to +70 C, with a fixed TPU bumper at each end. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries. For planning, treat roughly 343 N (about 60% of the 0.5 MPa rating) as usable work force, which lifts about 29 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED40X200 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED40X200 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED40X200
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED40X200 Is Used
Fixture clamping from both sides
A 200 mm through-rod lets one cylinder clamp a machined aluminium casting from the front while the rear rod drives a locator pin, delivering 571.8 N per side at 0.5 MPa in a jig too short for a full-length profile cylinder.
Conveyor pusher with rear flag
On a bottling line transfer, the front rod pushes cartons across a lane at 30-500 mm/s while the back rod carries a flag for a proximity sensor, using the symmetric 40 mm bore force of 800.5 N at 0.7 MPa.
Vertical lift of small pallets
With about 29 kg of vertical lift capacity at a 2:1 margin, the ACED40X200 raises small pallet trays or lids on a packaging machine, the through-rod keeping the load plate square without extra guides.
Is the Airtac ACED Double-acting Compact Cylinder ACED40X200 the Right Cylinder?
At 571.8 N both ways, the 40 mm bore sits between the 32 mm (345.6 N) and the 50 mm (881.2 N) options - pick 32 mm for lighter pick-and-place, 50 mm when you need roughly 1.5x the force. The 200 mm stroke is the maximum standard stroke for this bore, so no made-to-order length is required. Remember the piston drifts if air is lost; add a rod lock or pilot check for a held load. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the ISO 21287 face. This version has no magnet - order the -S code if you need CMSE / DMSE switch positions.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED40X200 FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal either way: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa, with a maximum of 116.6 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, -20 to +70 C, rod thread M8x1.25 female, 1/8" ports.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA/FB flange, LB foot or FTC brackets bolt straight to its face. A fixed TPU bumper at each end absorbs end-of-stroke impact. Sensors are possible only with the optional -S magnet code, which enables CMSE / DMSE switches; this standard ACED40X200 has no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED40X200
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.