Airtac ACED Double-acting Compact Cylinder ACED63X250S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X250S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 250mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke250 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X250S
A double acting ISO 21287 compact cylinder with a rod leaving both covers, the ACED63X250S delivers the same 1458.1 N at 0.5 MPa (2041.3 N at 0.7 MPa) on every stroke, since both sides work on the rod-side area. The 63 mm bore drives a 16 mm through-rod over a 250 mm stroke at 30-500 mm/s, with a fixed TPU bumper at each end to soften the stops.
The hard-anodized aluminium body with an S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into long-travel gantries and conveyor pushers where space is tight. This -S version carries the magnet, so CMSE / DMSE reed or solid-state switches can be clipped on for end-of-stroke signalling. At 0.5 MPa the thrust equates to roughly 148 kgf, so plan on lifting about 74 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED63X250S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X250S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X250S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X250S Is Used
Conveyor diverter pusher
The 250 mm stroke sweeps cartons across a belt line, and equal 1458.1 N force in both directions means the return stroke pushes just as hard as the extend.
Gantry pick-and-place flag carrier
The rear rod carries a sensor flag while the front rod does the work, and the fitted magnet feeds CMSE / DMSE switches for position feedback along the full travel.
Pallet strapping press
With about 74 kg of vertical lift capability at a 2:1 margin, the 63 mm bore presses strapping buckles or holds pallet corner boards during wrap.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X250S the Right Cylinder?
At 1458.1 N per side at 0.5 MPa, the 63 mm bore sits between the 50 mm (881.2 N) and 80 mm (2356.2 N) options - step down for lighter palletizing duty, up for heavy clamping. Air supply is 0.15-1.0 MPa (22-145 psi), ports are 1/8" PT, and the rod end carries a female M10x1.5 thread. Remember that a plain double-rod cylinder will drift if air is lost; add a rod lock or pilot check valve where a load must stay put. FA/FB flange, LB foot and FTC brackets bolt straight to the ISO 21287 face.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X250S FAQ
Yes - the double-rod design puts a piston rod through both covers, so every stroke uses the rod-side area. Force is 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in either direction, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, freeing space in sliding guards and tight gantries. This model carries the optional -S magnet, so CMSE / DMSE switches mount directly on the body slots for stroke-end detection. A fixed TPU bumper at each end absorbs the end-of-stroke shock, and FA/FB flange or LB foot brackets attach to the standard ISO 21287 face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X250S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.