Airtac ACED Double-acting Compact Cylinder ACED63X30SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X30SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 30mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke30 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X30SB
A double acting compact cylinder built to ISO 21287, the ACED63X30SB pushes a 63 mm bore through a 30 mm stroke with a rod leaving both covers. Because each side works on the rod-side area, output is identical in either direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. The male rod thread (B code) and PT ports suit direct screw-on tooling. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and fixtures.
The through-rod resists rotation and modest side load, and the rear rod can carry a sensor flag or a second tool. This S-code model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches mount directly in the body slots. A fixed TPU bumper at each end absorbs end-of-stroke shock.
Airtac ACED Double-acting Compact Cylinder ACED63X30SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X30SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X30SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X30SB Is Used
Symmetric press stations
The equal 1458.1 N output in both directions lets one ACED63X30SB load and eject aluminium die-cast housings on a machining cell fixture without recalibrating for stroke direction.
Reciprocating transfer beams
A rod on each cover drives a pick-and-place beam between two tool plates, with the rear rod doubling as a mount for a CMSE switch flag to confirm home position.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X30SB the Right Cylinder?
At 1458.1 N per direction, the 63 mm bore sits between the 50 mm (881.2 N at 0.5 MPa) and 80 mm (2356.2 N) classes - step down for lighter clamping, up for heavy press-fit work. Remember that a plain double-rod cylinder drifts when air is lost; add a rod lock or pilot check if the load must stay put. FA/FB flanges, LB feet and FTC brackets bolt to the ISO 21287 face, and the 30 mm stroke is well inside the 250 mm standard range for this bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X30SB FAQ
It is a double-rod, double-acting cylinder, so force is equal both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in each direction, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is 1/8" (PT).
The ISO 21287 short body cuts mounting length by roughly half compared with an ISO 15552 profile cylinder, and the hard-anodized aluminium body carries a hard-chrome S45C rod with fixed TPU bumpers at both ends. Because this is the S version, the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped into the body slots for end-of-stroke signalling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X30SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.