Airtac ACED Double-acting Compact Cylinder ACED63X35B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X35B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X35B
A double acting compact cylinder with a rod leaving both covers, the ACED63X35B delivers 1458.1 N in each direction at 0.5 MPa because both strokes work on the rod-side area of its 63 mm bore. The male rod thread (B code) bolts straight to tooling, and the through-rod resists rotation and side load while the free back-end rod can carry a sensor flag or a second fixture. Speed range is 30-500 mm/s and pressure runs 0.15-1.0 MPa (22-145 psi).
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this 35 mm stroke unit slots into tight gantries and guarding. A fixed TPU bumper at each end absorbs end-of-stroke shock, the hard-anodized aluminium body carries the 1/8" ports, and the S45C hard-chrome rod stands up to continuous cycling. At 0.5 MPa the rod-side force equals roughly 148 kg of lift; halve that for margin and you can raise about 74 kg vertically with confidence.
Airtac ACED Double-acting Compact Cylinder ACED63X35B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X35B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X35B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X35B Is Used
Reciprocating press transfer
The equal 1458.1 N force in both directions lets a 35 mm shuttle carry a steel die carrier out and back at the same speed on a stamping line.
Symmetric lift column
A rod on each cover gives balanced mounting points for a packaging machine lift table raising about 74 kg of product trays with a 2:1 margin.
Dual-end flag station
The back-end rod drives a target flag past a switch position on an assembly gantry, while the front rod does the clamping work.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X35B the Right Cylinder?
Step up from a 50 mm bore (881.2 N at 0.5 MPa) when your tooling needs the extra 1458.1 N this 63 mm double-rod unit gives both ways; step down to an 80 mm bore (2356.2 N) only if the 35 mm stroke and envelope allow it. Note that a plain double-rod cylinder drifts when air is lost, so pair it with a rod lock or pilot check for a held load. Foot, flange and FTC brackets bolt to the ISO 21287 face, and if you later need position feedback, order the -S code so CMSE / DMSE switches can be fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X35B FAQ
Because a rod exits both covers, force is equal in both directions: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, both ways. At the full 1.0 MPa rating the rod-side area of the 63 mm bore yields a maximum of 297.4 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure.
It is an ISO 21287 compact cylinder, roughly 50% shorter in mounting length than an ISO 15552 profile cylinder, with a hard-anodized aluminium body, S45C hard-chrome 16 mm rod, 1/8" PT ports and a fixed TPU bumper at each end. The magnet is not fitted on this code; order the -S version if you want CMSE or DMSE switches to work, and choose LB foot, FA/FB flange or FTC mounting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X35B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.