Airtac ACED Double-acting Compact Cylinder ACED63X55B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X55B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 55mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke55 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X55B
A double acting compact actuator built to ISO 21287, the ACED63X55B pushes a 16 mm rod out of BOTH covers, so thrust is identical on the extend and retract strokes. At 0.5 MPa the 63 mm bore delivers 1458.1 N in either direction, rising to 2041.3 N at 0.7 MPa. The male rod thread (B code) on each end bolts straight to your tooling.
The through-rod resists rotation and side load and gives a symmetric mount, and the rear rod can carry a sensor flag or a second fixture. The hard-anodized aluminium body with S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and guarding. Fixed TPU bumpers absorb end-of-stroke shock at both ends, speed spans 30-500 mm/s, and pressure runs 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof. For sizing, treat roughly 875 N (about 0.6 of the 0.5 MPa rating) as the practical working thrust, which lifts roughly 74 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED63X55B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X55B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 55 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X55B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X55B Is Used
Symmetric press fixture
The equal 1458.1 N thrust both ways suits a light staking or marking press where the same force must push and pull a forming die on the 55 mm stroke.
Reciprocating conveyor pusher
A rod on each cover lets one end drive the pusher plate while the rear rod carries a flag for a proximity sensor, cycling at up to 500 mm/s.
Gantry pick-and-place riser
The short ISO 21287 body fits under low gantry beams, and the through-rod balances a 74 kg vertical lift load with a 2:1 margin in a pick station.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X55B the Right Cylinder?
At 1458.1 N per side at 0.5 MPa this 63 mm double-rod unit sits between the 50 mm bore (881.2 N) and the 80 mm bore (2356.2 N), so step down for lighter clamping or up for heavy press-fit work. Keep in mind it will not hold position if air is lost - add a rod lock or pilot check for a held load. Mount with FA/FB flange, LB foot or FTC brackets plus I/Y rod knuckles on the ISO 21287 face. If you need CMSE or DMSE switch position feedback, order the optional -S magnet version; this base model has no magnet fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X55B FAQ
Yes - the double-rod design means both strokes use the rod-side area, so force is equal extending and retracting: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with fixed TPU bumpers at both ends and FA/FB, LB or FTC mounting options. Switches are possible only on the -S version: the optional -S magnet enables CMSE / DMSE sensors, while this base model ships without a magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X55B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.