This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED16X30, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD16X30
The AirTAC ACPD Double Rod Compact Cylinder ACPD16X30 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED16X30 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM4×0.7
- StatusDiscontinued → ACED16X30
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD16X30
This discontinued AirTAC ACPD16X30 is a double acting compact cylinder with a rod exiting BOTH covers, so it pushes and pulls with identical force: 75.4 N at 0.5 MPa and 105.6 N at 0.7 MPa in each direction, because both strokes work on the rod-side area. The through-rod resists rotation and light side load, gives a symmetric mount, and the rear rod can carry a sensor flag. Stroke is 30 mm on a 16 mm bore with an 8 mm rod, a female M4x0.7 rod thread and M5x0.8 ports.
The hard-anodized aluminium body with S45C hard-chrome rod is an ISO 21287 short build that saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures and gantries. A fixed TPU bumper sits at each end and speed runs 30-500 mm/s at 0.15-1.0 MPa (22-145 psi). Note: this model is discontinued - the current-production direct is ACED16X30, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD16X30 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD16X30 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED16X30 |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED16X30 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD16X30
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD16X30 Is Used
Small-parts ejection from fixtures
The 75.4 N dual-direction thrust on a 30 mm stroke ejects machined pins or plastic caps out of a drill jig, and the front rod thread M4x0.7 takes a custom ejector tip.
Flag-driven position sensing on transfer rails
The rear rod of the through-rod design carries a switch flag past CMSE or DMSE switches (with the optional -S magnet) to confirm slide position on an electronics assembly conveyor.
Light press-fit of connectors
About 45 N of usable force at 0.5 MPa presses USB or terminal blocks into PCB housings where a full-length cylinder would overhang the bench.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD16X30 with the ACED16X30
At 75.4 N per direction at 0.5 MPa, the 16 mm bore suits light clamping and small part transfer; step down to the 12 mm bore (42.4 N) for tighter spaces or up to 20 mm (117.8 N) when you need more push. The through-rod suits symmetric tooling and the rear rod can drive a switch flag. If a load must stay put when air is lost, add a rod lock or pilot check - this cylinder drifts. Mounting brackets and I/Y knuckles bolt to the ISO 21287 face, and CMSE / DMSE switches work only if you order the optional -S magnet code. Replacement: ACED16X30.
Replacement checklist
- ✓ Current-production ACE → ACED16X30
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD16X30 FAQ
Yes - the double-rod design means both strokes use the rod-side area, so force is equal either way: 75.4 N at 0.5 MPa and 105.6 N at 0.7 MPa, with a maximum of 15.4 kgf at 1.0 MPa.
It is an ISO 21287 compact build whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end. This model is discontinued; the current direct is ACED16X30 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before you swap.
Request a Quote for the ACED16X30
Send us the quantity and destination. We confirm price, stock and lead time on the ACED16X30 replacement — usually within 7-8 hours.