This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED25X35S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD25X35S
The AirTAC ACPD Double Rod Compact Cylinder ACPD25X35S is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø25mm bore and 35mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED25X35S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ25 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- StatusDiscontinued → ACED25X35S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD25X35S
This ACPD25X35S is a double acting compact cylinder with a rod leaving both covers, so the 25 mm bore delivers 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa in each direction - both strokes work on the rod-side area. The 10 mm through-rod resists rotation and side load, and the rear rod can carry a sensor flag while the front rod drives the tool. A fixed TPU bumper sits at each end, and speed spans 30-500 mm/s.
The hard-anodized aluminium body is an ISO 21287 short build that saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it suits tight jigs and gantries. Note that this model is discontinued: the current-production direct is the ACED25X35, so confirm ISO 21287 mounting dimensions before swapping. The S in the code means the optional -S magnet is fitted, so CMSE / DMSE switches can be added.
Airtac ACPD Double Rod Compact Cylinder ACPD25X35S Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD25X35S |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED25X35S |
| Bore size | Ø25 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED25X35S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD25X35S
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD25X35S Is Used
Fixture clamping from both sides
The through-rod lets a jig clamp a machined aluminium bracket on the front rod while the rear rod trips a CMSE switch confirming full clamp - 206.2 N per side at 0.5 MPa.
Gantry pick-and-place with position feedback
In a 35 mm stroke electronics assembly gantry, the fitted -S magnet and DMSE switches report extend and retract, and the symmetric double-rod mount resists side load on small PCB trays.
Push-pull slide on a packaging line
A carton rejector slide needs equal force both ways; the 288.6 N at 0.7 MPa in each direction and fixed TPU bumpers at both ends suit the rapid 30-500 mm/s cycling.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD25X35S with the ACED25X35S
At 206.2 N per side at 0.5 MPa, this 25 mm unit sits between the 20 mm bore (117.8 N) and the 32 mm bore (345.6 N) - step up to 32 mm if your fixture needs more margin, or down to 20 mm for lighter pick-and-place work. Remember the piston drifts when air is lost; add a rod lock or pilot check if the load must stay put. FA/FB flange and LB foot mountings bolt to the ISO 21287 face, and the fitted -S magnet accepts CMSE / DMSE switches. Since the ACPD line is discontinued, order the ACED25X35 as the current replacement and verify mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACED25X35S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD25X35S FAQ
Yes - the double-rod design means both strokes use the rod-side area, so force is equal each way: 206.2 N at 0.5 MPa, 288.6 N at 0.7 MPa, and a maximum of 42.0 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, and speed runs 30-500 mm/s.
AirTAC no longer produces the ACPD series. The current direct is the ACED25X35 (swap the P for an E), which matches the same 25 mm bore, 35 mm stroke and force class in the ISO 21287 family - confirm mounting dimensions before swapping since the ACP is DIN-standard. On this S-coded unit the optional -S magnet is fitted, so CMSE / DMSE reed or solid-state switches mount directly on the body.
Related AirTAC ACE Cylinders
Request a Quote for the ACED25X35S
Send us the quantity and destination. We confirm price, stock and lead time on the ACED25X35S replacement — usually within 7-8 hours.