This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X200B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200B
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X200B is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X200B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X200B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X200B
Double acting with a rod leaving both covers, the ACPD32X200B is a DIN-standard compact cylinder in the 32 mm bore class. Because each stroke works on the rod-side area, output is identical in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The 200 mm stroke sits right at the maximum standard stroke for this bore, and the male rod thread (B code) bolts straight to external tooling.
The hard-anodized aluminium body is an ISO 21287 short build, saving about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and guarding. The through-rod resists rotation and side load and gives a symmetric mount, and the rear rod can carry a sensor flag. Fixed TPU bumpers sit at both ends, speed runs 30-500 mm/s, and pressure spans 0.15-1.0 MPa (22-145 psi). Note: this model is discontinued - the current-production direct is the ACED32X200, so confirm ISO 21287 mounting dimensions before swapping. Also, without the optional -S magnet no CMSE or DMSE switch can be fitted.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200B Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X200B |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X200B |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X200B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X200B
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X200B Is Used
Reciprocating transfer gantry
The through-rod drives a carriage from either cover with equal 345.6 N thrust both ways across the full 200 mm travel, keeping the motion symmetric on a pick-and-place beam.
Fixture clamp with rear sensor flag
On a CNC jig, the back-end rod carries a flag past a switch position to confirm clamp state, while the front rod delivers about 207 N of usable clamping force at 0.5 MPa.
Conveyor pusher station
A male-threaded pusher pad on the front rod deflects cartons off a line, and the rear rod doubles as a guide or position reference over the 200 mm stroke.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X200B with the ACED32X200B
At 345.6 N per direction, bore 32 suits clamping and transfer jobs in the 20-30 kg range; step down to bore 25 (206.2 N) for lighter pick-and-place or up to bore 40 (571.8 N) when the load grows. The 200 mm stroke is the maximum standard for this bore, so longer travels become made-to-order. Remember the piston drifts if air is lost - add a rod lock or pilot check where a load must stay put. FA/FB flange and LB foot mountings bolt to the ISO 21287 face, and the male rod thread (B) takes standard rod knuckles. Order the -S code if you need the magnet for CMSE / DMSE switches; this bare code has none. For new builds, specify the ACED32X200 instead - this ACPD is discontinued.
Replacement checklist
- ✓ Current-production ACE → ACED32X200B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X200B FAQ
Yes - the double-rod design means both strokes use the rod-side area, so output is equal either way: 345.6 N at 0.5 MPa, 483.8 N at 0.7 MPa, and a maximum of 70.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof, speed 30-500 mm/s, and the fixed TPU bumpers decelerate at each end. As a rule of thumb, count on about 207 N of real work at 0.5 MPa, roughly a 21 kg vertical lift.
The ACPD family is no longer in production. The current direct is the ACED32X200 (swap the P for an E), which matches the same 32 mm bore, 200 mm stroke and force class in the ISO 21287 short body - confirm the mounting dimensions before swapping, since the ACP is DIN-standard. On the ACPD itself, the magnet was never fitted unless you ordered the optional -S code; this bare B-suffix unit has no magnet, so no CMSE or DMSE switch can be mounted on it.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X200B
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X200B replacement — usually within 7-8 hours.