This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X200SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X200SB is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X200SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X200SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB
This is a double acting compact cylinder with a rod leaving both covers, so the through-rod pushes and pulls with identical force: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa in either direction. The 32 mm bore drives a 12 mm rod over a 200 mm stroke at 30-500 mm/s, with 1/8" ports, a male rod thread (B code) and the -S magnet fitted so CMSE / DMSE switches can be mounted. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), temperature -20 to +70 C.
The hard-anodized aluminium body follows the ISO 21287 short format, cutting roughly 50% off the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs and guarding. Because both rod ends are exposed, the rear rod can carry a sensor flag or a second tooling plate while resisting side load. Note the fixed TPU bumper only decelerates at each end - it never holds position, so add a rod lock or pilot check for a suspended load. This model is discontinued; the current-production successor is ACED32X200, and you should confirm the ISO 21287 mounting dimensions before swapping since the ACP was DIN-standard. As a sizing rule, treat about 207 N (roughly 21 kg vertical) as the usable working force at 0.5 MPa rather than the full rating.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X200SB |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X200SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB Is Used
Symmetric clamp fixture
A machining centre fixture uses the through-rod to clamp a housing from both sides with equal 345.6 N force, eliminating a second cylinder and keeping the jig under 50% of an ISO 15552 length.
Two-sided pusher on a packaging line
The rear rod drives a synchronized reject plate while the front rod pushes cartons off a conveyor, both directions delivering 483.8 N at 0.7 MPa over the full 200 mm travel.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB with the ACED32X200SB
At 345.6 N per direction, bore 32 suits clamping and transfer tasks in the 20-30 kg class; step down to bore 25 (206.2 N) for lighter fixtures or up to bore 40 (571.8 N) when the load grows. The 200 mm stroke is the maximum standard stroke for this bore, so no made-to-order build is needed. FA/FB flange and LB foot mountings bolt to the ISO 21287 face, and the -S magnet already carried by this code accepts CMSE / DMSE switches for end-of-stroke sensing. For new designs, order the ACED32X200 instead - it is the current direct for this discontinued model.
Replacement checklist
- ✓ Current-production ACE → ACED32X200SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X200SB FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal each way: 345.6 N at 0.5 MPa, 483.8 N at 0.7 MPa, and a maximum of 70.5 kgf at 1.0 MPa. Speed range is 30-500 mm/s and operating pressure is 0.15-1.0 MPa (22-145 psi).
Order the ACED32X200, the current-production ISO 21287 successor made by swapping the P for an E. It matches the same 32 mm bore, 200 mm stroke and force class, but confirm the ISO 21287 mounting dimensions against your fixture first, since the ACP was built to a DIN-standard footprint. Outline dimensions for the old model: confirm from datasheet.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X200SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X200SB replacement — usually within 7-8 hours.