Airtac MID Series Double Rod Mini Cylinder MID25X10
The AirTAC Airtac MID Series Double Rod Mini Cylinder MID25X10 is a genuine double acting, double rod round-body mini air cylinder with a Ø25mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.25
- CushionFixed TPU bumper pads
About the Airtac MID Series Double Rod Mini Cylinder MID25X10
Delivering 206.1 N of thrust at 0.5 MPa in both directions, the AirTAC MID25X10 is a 25 mm bore double-acting through-rod mini cylinder. Because a rod exits both end covers, the extend and retract areas are identical, ensuring equal force while the twin-rod geometry resists rotation and side loads for steady guiding. The stainless-steel round barrel and piston rod provide mild corrosion resistance for washdown environments. It uses a 1/8" port and an M10x1.25 male rod thread.
Built to the ISO 6432 mounting interface, this riveted round-body unit drops into standard mini brackets and clevises. It generates a safe working load of roughly 124 N and can vertically lift about 10.5 kg with a 2:1 safety margin. The fixed TPU bumper pads decelerate the stroke ends, though the piston will drift on air loss as the bumpers are not a locking mechanism.
Airtac MID Series Double Rod Mini Cylinder MID25X10 Technical Specifications
| Model | Airtac MID Series Double Rod Mini Cylinder MID25X10 |
|---|---|
| Series | MID ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed TPU bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac MID Series Double Rod Mini Cylinder MID25X10
| MID | ISO 6432 round-body mini cylinder (double-rod). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MID Series Double Rod Mini Cylinder MID25X10 Is Used
Guided Push Station
Uses the 206.1 N equal force and twin-rod anti-rotation to deliver steady, non-twisting pushes for aligning light parts.
Symmetric Shuttle
Drives a 10.5 kg payload back and forth, leveraging the through-rod to mount a stop or flag on the rear end.
Back-Rod Switch Trip
The extended rear rod trips an external mechanical switch, ideal for space-constrained 10 mm stroke sequencing.
Is the Airtac MID Series Double Rod Mini Cylinder MID25X10 the Right Cylinder?
If you need less force, the MID20 bore provides 131.9 N at 0.5 MPa; for heavier moves, the MID32 offers 345.6 N. The twin-rod design is ideal here for light jobs needing anti-rotation stability, a back-rod switch trip, or a symmetric shuttle drive without external guides. For position holding under air loss, add an external rod lock or pilot check valve, as the bumper pads only soften the end of stroke. Mount via LB foot, FA flange, or TC trunnion (the SDB pivot block is unavailable for double-rods). This SKU lacks a magnet, so it cannot take CMSG/DMSG/EMSG sensors; specify the -S variant for sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MID Series Double Rod Mini Cylinder MID25X10 FAQ
It delivers equal force both ways due to the double-rod design: 206.1 N at 0.5 MPa, 288.5 N at 0.7 MPa, and a maximum theoretical force of 42.0 kgf at 1.0 MPa. The 1/8" port supplies air for 30-800 mm/s speeds.
No, this specific SKU does not include a magnet and cannot accept CMSG, DMSG, or EMSG sensors. You must select the -S variant to enable magnetic sensing. The stainless steel build resists mild corrosion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MID Series Double Rod Mini Cylinder MID25X10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.